Handling The Equipment - Dexter power TS8 Traduction Des Instructions D'origine

2. Make sure that the holder (16) is aligned parallel to
the saw blade (5). If necessary, readjust it with the
aid of the scale (38).
3. Slide the sliding block along the groove (37) in the
stop rail (17).
4. Fasten the stop rail (17) to the holder (16) with the
help of the screws (16a).
8.8 Fitting the transverse stop (fig. 18)
1. Slide the transverse stop (2) in the groove (40) of
the saw table (1).
2. Loosen the turning handle (19).
3. Turn the transverse stop (2) until the arrow points
to the desired angle.
4. Retighten the turning handle (19).
8.9 Chip extraction (fig. 13)
ATTENTION: Only operate the device with an extrac-
tion
system.
Connect a suitable chip extraction system (not includ-
ed in the scope of delivery) to the suction port (36).
ATTENTION: Check and clean the suction channels
at regular intervals.
8.10 Stable fastening (fig. 25)
The machine must be securely installed, i.e. bolted
down on a workbench, machine stand or similar, as
shown in fig. 25.
Use the bracket for workbench mounting (42), the
screws (43) and the washers (44) to do so.

9. Handling the equipment

9.1 Switches (fig. 1)
9.1.1 On/off switch (11)
• It is possible to switch the saw on by pressing the
green "I" button. Before starting sawing, wait until
the saw blade has reached its maximum speed.
• In order to switch the saw off again, it is necessary
to press the red "0" button.
9.1.2 Overload switch (10)
The device motor is protected against overload with
an overload switch (10).
In the event of the nominal current being exceeded,
the overload switch (10) switches the device off.
If this happens, proceed as follows:
• Let the device cool down for several minutes.
• Press the overload switch (10).
• Switch the device on by pressing the green "I" but-
ton.
-
9.2 Setting the cutting depth (fig. 1)
The saw blade (5) can be adjusted to the required cut-
ting depth by turning the hand wheel (8).
• Counter-clockwise: Greater cutting depth
• Clockwise: Smaller cutting depth
Check the setting with a test cut.
9.3 Setting the angle (fig. 14)
Angled cuts of 0°-45° to the left of the parallel stop (7)
can be carried out with the circular table saw.
m Before making every cut, check that no collision
can occur between the stop rail (17), transverse stop
(2) and the saw blade (5).
1. Loosen the locking handle (9).
2. Set the desired angle on the scale by turning the
hand wheel (8).
3. Lock the locking handle (9) at the desired angle setting.
9.4 Using the parallel stop (fig. 2, 15-17)
9.4.1 Stop heights (fig. 15, 16)
• The stop rail (17) of the parallel stop (7) has two
guide surfaces at different heights.
• Depending on the thickness of the material to be
cut, the stop rail (17) must be used as shown in Fig.
15 for thick material (workpiece thickness exceed-
ing 25 mm) and as shown in Fig. 16 for thin material
(workpiece thickness below 25 mm).
9.4.2 Shifting the stop rail (fig. 15, 16)
1. In order to move the stop rail (17) to the lower
guide surface, loosen the two screws (16a) to re-
lease the stop rail (17) from the holder (16).
2. Pull the stop rail (17) along the groove and out.
3. Turn the stop rail (17) and slide the sliding block
along the second groove (39).
4. Shifting to the higher guide surface must be car-
ried out in the same way.
9.4.3 Cutting width (fig. 15, 16)
• The parallel stop (7) must be used when cutting
sections of wood lengthways.
• The parallel stop (7) can be mounted on both sides
of the saw table (1).
• The parallel stop (7) can be set to the required di-
mension with the aid of the scale (38) on the saw
table (1).
• Tighten the two locking knobs (15) to fasten the par-
allel stop (7) in place.
• Perform a test cut to measure the width before cut-
ting the real workpiece. In this way you avoid inac-
curacies with the scale or the setting.
9.4.4 Setting the stop length (fig. 15, 17)
In order to avoid the material to be cut becoming
jammed, the stop rail (17) can slide in a longitudinal
direction.
GB | 33