Operation; Switching On/Off; Working With The Chainsaw - EINHELL BG-LC 1815 T Mode D'emploi D'origine

If the rechargeable battery pack fails to charge,
check whether there is voltage at the socket
outlet.
If you still fail to charge the battery pack, please
return the complete tool together with the battery
charger to our Customer Service Center.
Timely recharging of the battery will help it serve
you well for a long time. You must recharge the
battery pack when you notice that the perfor-
mance of the equipment drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.

6. Operation

Please note that the statutory regulations gover-
ning noise abatement may diff er from one loca-
tion to another.
6.1 Using the shoulder strap
Caution! Always use the shoulder strap when
working with the equipment. Switch off the equip-
ment before you take off the shoulder strap (risk
of injury).
1. Slip the shoulder strap over your shoulder.
2. Adjust the length of the shoulder strap so that
the strap attachment is at waist level.
6.2 Setting the telescopic tube (Fig. 11)
1. Open (a) the telescopic tube lock (12).
2. Pull out the top telescopic tube (11) until it
reaches the required working height.
3. Close (b) the telescopic tube lock (12) again.
6.3 Switching on/off
Switching on
•
Hold the pole-operated pruner firmly with one
hand on the handle (Fig. 1/item 3) and the
other hand on the grip area (Fig. 1/item 13).
•
(Fig. 12) Pull back the switch lock (4) and
press the ON/OFF switch (2).
Switching off (Fig. 12)
Release the ON/OFF switch (2) and then the
switch lock (4).
Anleitung_BG_LC_1815_T_SPK7.indb 23 Anleitung_BG_LC_1815_T_SPK7.indb 23
GB

7. Working with the chainsaw

Preparations
To ensure that you can work safely, check the fol-
lowing points before every use:
Condition of the chainsaw
Inspect the chainsaw before the start of work for
damage to the housing, the power cable, the saw
chain and the cutter rail. Never use a chainsaw
which is obviously damaged.
Oil container
Level of oil in the oil container: Both before and
during your work make sure that there is always
suffi cient oil in the system. To avoid damaging the
chainsaw, never run the saw if there is no oil in the
system or if the oil drops below the „min" mark.
On average, a single fi lling will last around 15
minutes depending on the number of pauses in
cutting and the loads involved.
Chain
Tension of the chain, condition of the cutting
elements: The sharper the chain, the easier and
more controllable it is to operate the chainsaw.
The same also applies to the chain tension. For
greater safety you must check the chain tension
before your work and at least every 10 minutes
during your work. New chains in particular tend to
expand more.
Safety clothing
Always wear appropriate tight-fi tting safety
clothing such as special trousers which protect
against cuts, protective gloves and safety shoes.
Hearing protection and protective goggles.
Wear a protective helmet with integral face and
hearing protection. This will off er protection
against falling branches and recoiling branches.
Safe working
•
To ensure that you can work in safety you
must use the equipment at a working angle of
max. 60°.
•
Never stand under the branch you want to
saw.
•
Use special caution when working with bran-
ches under tension and splintering wood.
•
Possible risk of injury caused by falling bran-
ches and catapulting pieces of wood.
•
When the equipment is in operation, keep
other persons and animals away from the
- 23 -
31.10.11 10:27 31.10.11 10:27