Milwaukee REDSTICK DIGITAL LEVEL 60 Notice Originale page 13

MEASUREMENT 0° / 90° / PIN
When the level is within 3° of the target
measurement, directional indicators
2.14
will appear and move in the direction
needed to achieve the target.
If the sound is on, the beats per minute
will change once you are within 5°. If
3.52
the target is crossed, the pitch will also
change, indicating a passed target.
0.00
When the target is achieved within the
tolerance range set by the user, the
background will turn green (if 0°or 90°)
or blue (if PIN). If the sound is on, the
on target tone will also play.
15.26
PIN MODE
A pin can be set to provide a custom target measurement
other than 0° and 90°.
To set the PIN, place the level at the desired measurement
and press .
2
1
In PIN Mode the background will turn blue.
To adjust the PIN, press and hold
PIN. Adjust to the exact measurement with
Press once more to set the new PIN.
A PIN list stores commonly used measurements and recent
PINS. To enter the PIN list, press and hold
. Select a PIN with
To turn off the PIN mode and return to 0° and 90° as targets,
press again while in working mode.
IN-FIELD LEVEL CHECK BEST PRACTICE
To verify the level is within factory specifi cations, follow the
below instructions:
1. Set the level to the following:
Mode = Angle
Sensitivity = Hundredths
Tolerance = 0.00
2. Place the level on a known fl at, even surface with the
main display facing forward. Mark a line on the surface to
note the exact location.
3. Record the measurement displayed as well as the
direction of the rotation.
470 207 - Digital Level.indd 13 470 207 - Digital Level.indd 13
15.26
again to set a new
.
and then
. Set a PIN with .
The direction of the rotation is determined by the direction
of the rotating indicators on the display.
2.14
4. Rotate the level 180°.
Reference the line marked in step 2 to ensure the level is
placed in the exact same location.
5. Record a second measurement, again noting the
direction of the rotation.
6. Add the fi rst measurement to the second measurement.
Then, divide by two to determine the level's variance.
NOTE: If the diff erence is between 0.00 and 0.05, the level
is within the accurate range. If not, please contact a
MILWAUKEE service facility.
PRECISION MEASURING
All levels read slightly diff erent from one end to the other. As
a result, you may see variance in some readings. In order to
provide the most precise measurement, you can use the
practice described in previous chapter.
CHARGING
Plug your USB cable into a power source such as an AC
wall adaptor, computer or car port.
The indicator light will display the charging status:
Red solid: charging, 0-79% charged
Green fl ashing: charging, 80-99% charged
Green solid: 99-100% charged
Red/Green fl ashing: damaged or faulty battery
If the light indicator fl ashes red and green, check that the
battery is fully seated into the bay. Remove the battery and
reinsert. If the light continues to fl ash red and green, the
battery may be extremely hot or cold, or wet. Allow the
battery to cool down, warm up, or dry out and then reinsert.
If the problem persists, contact a MILWAUKEE service
facility.
BATTERIES
Battery packs which have not been used for some time
should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the
performance of the battery pack. Avoid extended exposure
to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept
clean.
For an optimum life-time, the battery packs have to be fully
charged, after used.
To obtain the longest possible battery life remove the battery
pack from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C
and away from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
ENGLISH
2.14
13
24.06.2019 15:02:46 24.06.2019 15:02:46