Gaggenau DF 260 Notice D'utilisation page 20

Problem Cause
Dishwasher not 1.
illing with water 2.
3.
Water Leaks 1.
2.
3.
4.
Tub stains 1.
2.
Streaks on glass- Incorrect rinse agent seing.
ware or residue
on the dishes
Fascia panel Abrasive cleaner used.
discolored or
marked
Noise during The dishes may not be arranged properly.
wash cycle
Detergent dis- 1.
penser cover will 2.
not shut
Unable to select Previous cycle has not inished.
desired cycle
Error Codes If fault code (E01 to E30) is indicated on the digital display 3 , irst disconnect the appliance from the power supply. You can
recify certain faults yourself (see following fault descripion), for all other faults please contact customer service and state the
indicated fault E:XX.
Water is let in 1.
the appliance 2.
at the end of the
program
3.
4.
"Check water 1.
supply" display 2.
lights up 3.
4.
20
Restricion in the water supply system.
Previous wash cycle was not completed.
Delay-start is acive.
Suds
Door seal could be pulled away from basket.
Condensaion vent is blocked.
Improper installaion.
Stains on the dishwasher interior are due to hard-
ness of water.
Silverware in contact with tub.
Improper operaion of detergent cover.
Previous cycle has not been inished, reset, or cycle
was interrupted.
(E24) Waste water hose is blocked or kinked.
(E25) Waste water pump blocked, cover on the
waste water pump is not locked in posiion
Filters blocked.
The program has not yet ended.
Tap turned of.
Water supply interrupted.
Supply hose kinked.
Filter in the water supply blocked
Acion
1. Ensure that the water supply valve (typically located under kitch-
en sink) is open and check that the water supply line has no kinks
and clogs.
2. Refer to the "Canceling or changing the cycle" secion of this
manual.
3. Cancel the delay-start or wait unil delay-start ime completes
(imes out). Refer to the "Delay Start" secion of this manual.
1. Wrong type of detergent results in suds and leaks. Use only
dishwasher detergents. If suds sill persist, then add one ta-
blespoon of vegetable oil at the botom of the dishwasher
and run the desired cycle.
2. Ensure that door seal is in the track.
3. Ensure that condensaion vent is not blocked. Refer to "Load-
ing Extra Tall Items" in the Preparing and Loading the Dish-
washer secion of this manual.
4. Have proper installaion veriied by qualiied personnel (wa-
ter supply, drain system, leveling, plumbing).
1. Concentrated Lemon juice can reduce the build up of hard
water stains. Run a normal cycle unil it lushes and interrupt
the cycle and then place an 8 oz. cup of the concentrated lem-
on soluion on the top basket and inish the cycle. This can be
done periodically to avoid build up.
2. Ensure that the silverware does not make contact with the
tub while running a cycle.
Depending on the hardness of water, adjust the rinse agent dis-
penser. Refer to "Adding Detergent and Rinse Agent" secion in this
manual for adjustment.
Use mild detergents with sot damp cloth.
Water circulaion sound is normal, but if you suspect items are
banging into each other or into the spray arms, refer to the "Pre-
paring and Loading" secion of this manual for opimal arrange-
ment.
1. Refer to "Adding Detergent and Rinse Aid" secion of this man-
ual for instrucions on opening and closing the dispenser.
2. Refer to the "Canceling or changing the cycle" secion of this
manual.
Refer to the "Canceling or changing the cycle" secion of this
manual.
1. See Care and Maintenance.
2. Wait unil program ends (digital display indicates 0:00) or
implement the "Reset"funcion.
1. Switch of the appliance and pull out the main plug.
2. Turn of the tap.
3. Clean ilter in the supply hose.
4. Reconnect power supply.
5. Turn on the tap.
6. Switch on the appliance.