Nolan N21 VISOR Sécurité Et Instructions D'utilisation page 7

WARNING
- Push the left side slider completely downwards (Fig. 7 A) and upwards (Fig. 7 B) to make sure that the VPS works
properly. If necessary, repeat the above-mentioned steps.
- If the VPS opening/closing mechanisms are damaged or not working properly, please contact a Grex authorized
dealer.
- Do not use the helmet if the VPS has not been assembled properly.
- Since the VPS does not assure you the same protection as the one provided by the visor, it has to be used only
when the helmet visor is lowered.
VPS LOWER EDGE TRIM
The lower VPS sunscreen profile is moulded with a printed trim attached to the visor with fastening elements.
7. VPS Trim Disassembly
To release the trim from the lower edge of the sunscreen, first remove the sunscreen from the helmet (see instructions
above).
7.1. Pull the trim right end downwards to release the first fastening from the sunscreen (Fig. 9).
7.2. Continue releasing the other fastenings one by one, moving towards the other end of the sunscreen (Fig. 10).
7.3. Pull out the trim from the sunscreen left side flap (Fig. 10).
7.4. Release the trim left end and completely remove it from the sunscreen (Fig. 11).
8. VPS Trim Assembly
8.1. Insert the left side flap of the sunscreen in its slot on the trim (Fig. 12).
8.2. Press the trim left end against the sunscreen to attach it to the relevant fastening element (Fig. 10).
8.3. Continue attaching the other fastenings one by one, moving towards the other end of the sunscreen (Fig. 10).
8.4. Press the trim right end against the sunscreen to attach it to the relevant fastening element (Fig. 9).
8.5. Push the trim against the sunscreen aligning it with all the fastening device in order to attach it evenly along the
whole sunscreen lower edge; check that all the fastening devices are correctly attached and that the trim and the
visor fit together tightly. Finally, fit the sunscreen on the helmet (see instructions above).
WARNING
- Never use the helmet without having correctly assembled the sunscreen trim
- Make sure the VPS operates correctly by moving the left side slider downwards (Fig. 7A) and upwards (Fig. 7B)
and check that the visor lower edge trim does not come out of the sunscreen. If necessary, repeat the above-men-
tioned steps.
- In case of malfunctioning or damages, please contact an authorized Nolan dealer.
WARNING
- Push the left side slider completely downwards (Fig. 7 A) and upwards (Fig. 7 B) to make sure that the VPS works
properly. If necessary, repeat the above-mentioned steps.
- If the VPS opening/closing mechanisms are damaged or not working properly, please contact a Grex authorized
dealer.
- Do not use the helmet if the VPS has not been assembled properly.
- Since the VPS does not assure you the same protection as the one provided by the visor, it has to be used only
when the helmet visor is lowered.
VPS LOWER EDGE TRIM
The lower VPS sunscreen profile is moulded with a printed trim attached to the visor with fastening elements.
7. VPS Trim Disassembly
To release the trim from the lower edge of the sunscreen, first remove the sunscreen from the helmet (see instructions
above).
7.1. Pull the trim right end downwards to release the first fastening from the sunscreen (Fig. 9).
7.2. Continue releasing the other fastenings one by one, moving towards the other end of the sunscreen (Fig. 10).
7.3. Pull out the trim from the sunscreen left side flap (Fig. 10).
7.4. Release the trim left end and completely remove it from the sunscreen (Fig. 11).
8. VPS Trim Assembly
8.1. Insert the left side flap of the sunscreen in its slot on the trim (Fig. 12).
8.2. Press the trim left end against the sunscreen to attach it to the relevant fastening element (Fig. 10).
8.3. Continue attaching the other fastenings one by one, moving towards the other end of the sunscreen (Fig. 10).
8.4. Press the trim right end against the sunscreen to attach it to the relevant fastening element (Fig. 9).
8.5. Push the trim against the sunscreen aligning it with all the fastening device in order to attach it evenly along the
whole sunscreen lower edge; check that all the fastening devices are correctly attached and that the trim and the
visor fit together tightly. Finally, fit the sunscreen on the helmet (see instructions above).
WARNING
- Never use the helmet without having correctly assembled the sunscreen trim
- Make sure the VPS operates correctly by moving the left side slider downwards (Fig. 7A) and upwards (Fig. 7B)
and check that the visor lower edge trim does not come out of the sunscreen. If necessary, repeat the above-men-
tioned steps.
- In case of malfunctioning or damages, please contact an authorized Nolan dealer.
7
7