RIDGID R2401 Manuel D'utilisation page 8

ASSEMBLY
WARNING:
If any parts are damaged or missing do not operate
this product until the parts are replaced. Use of
this product with damaged or missing parts could
result in serious personal injury.
WARNING:
Do not attempt to modify this tool or create
accessories not recommended for use with this
tool. Any such alteration or modification is misuse
and could result in a hazardous condition leading
to possible serious personal injury.
WARNING:
Do not connect to power supply until assembly
is complete. Failure to comply could result in
accidental starting and possible serious personal
injury.
REMOVING THE BASE
See Figure 2, page 14.
 Unplug the trim router.
 Pull the quick release lever to the open position.
 Get a firm grasp of the base with one hand. Hold the
overmolded grip area with the other.
 Depress the motor release lever completely. Then pull the
motor housing away from the base until they seperate.
To connect the motor housing to the base:
 Depress the motor release lever completely.
 Align the motor housing with the base and push the motor
housing onto the base.
NOTE: This may require some force to overcome the
motor retention spring.
 Release the motor release lever and close the quick re-
lease lever.
WARNING:
If you are changing a cutter immediately after
use, do not touch the collet nut, cutter, or collet
with your hands or fingers as they may be hot.
Always use the wrenches provided to avoid getting
burned.
INSTALLING AND REMOVING CUTTERS
See Figures 3 - 4, page 14.
Cutters can be installed two ways.
To install a cutter using the spindle lock:
 Unplug the trim router.
 Pull the quick release lever to the open position.
 Depress the motor release lever and move the base to
provide clear access to the collet nut. It is not neccesary
to remove the base.
 Depress the spindle lock button and rotate spindle until
the spindle locks.
 Rotate the wrench counterclockwise to loosen the collet
nut. The collet is machined to precision tolerances to fit
cutters with 1/4 in. diameter shanks.
 If installing the cutter for the first time, it can be installed
once the collet nut is loose. If changing cutters, the cutter
will easily slip from the collet after loosening the collet nut.
NOTE: The tip of the cutter has a protective wax coating
that must be removed before first-time use. Simply peel
off the wax coating and be sure that all traces of wax are
removed before using the trim router.
 Insert the shank of the cutter into the collet until it touches
the bottom, then pull it out approximately 1/16". This
allows for expansion when the cutter gets hot.
 Tighten collet nut securely, by rotating it clockwise, using
large end of wrench.
 Depress the motor release lever and return the base back
to an operating position.
 Push the quick release lever to the closed position.
To install a cutter using two wrenches:
 Unplug the trim router.
 Pull the quick release lever to the open position.
 Remove the base to provide clear access to the collet nut.
 Lay flat on a stable workbench.
 Place the small end of one of the wrenches provided on
the spindle flats. This will hold the spindle stationary.
 Place the larger end of the other wrench provided onto
the collet nut. Rotate the wrench counterclockwise to
loosen the collet nut. The collet is machined to precision
tolerances to fit cutters with 1/4 in. diameter shanks.
 If installing the cutter for the first time, it can be installed
once the collet nut is loose. If changing cutters, the cutter
will easily slip from the collet after loosening the collet
nut.
NOTE: The tip of the cutter has a protective wax coating
that must be removed before first-time use. Simply peel
off the wax coating and be sure that all traces of wax are
removed before using the trim router.
 Insert the shank of the cutter into the collet until it touches
the bottom, then pull it out approximately 1/16". This
allows for expansion when the cutter gets hot.
 Tighten collet nut securely, by rotating it clockwise, using
large end of wrench.
 Connect the motor housing to the base and return the
base back to an operating position.
 Push the quick release lever to the closed position.
8 - English