EINHELL Expert GE-TM 102 B&S Mode D'emploi D'origine page 25

Important. Explosive gas is generated during the
charging process. This could collect under the co-
ver if closed and lead to explosive ignition. When
you charge the battery, refer to the safety regulati-
ons supplied by the battery manufacturer.
Important. Explosive gas can be generated du-
ring the charging process. You should therefore
avoid spark formation and naked fl ames during
the charging process.
Fitting the driver's seat (Fig. 16)
Fit the seat (Item 4) as shown. Adjust the position
of the seat by moving it in the slots. Adjust it to a
comfortable sitting position and make sure that
you can reach all of the control levers and pedals
easily.
Grass basket assembly (Fig. 17-24)
•
Fig. 17: Spread the grass basket out in front
of you. Fit the handle (Item 40).
•
Fig. 18: Fasten the bar (Item 20) to the bottom
part of the grass basket with the screws (Item
28), nuts (Item 29) and washers (Item 30).
•
Fig. 19: Swing the top part of the grass basket
up.
•
Fig. 20: Fasten the top part of the grass bas-
ket to the bar (Item 20) with the screws (Item
28), nuts (Item 29) and washers (Item 30).
•
Fig. 21-22: Fit the two support struts (Item a).
Use the screws (Item c) and nuts (Item b) to
do so.
•
Click the plastic rail (Item k) into the bar.
•
Fig. 23: Push the release lever for the grass
basket (Item 2) into the assembly opening on
the grass basket and secure it with the screw
(Item 28) and nut (Item 29) to prevent it from
working its way out.
Important.
Ensure that all screws are secure.
•
Fig. 24: Fully assembled grass basket.
Fitting the grass basket to the tractor lawn
mower (Fig. 25-29)
•
Fig. 25-26: Attach the grass basket to the at-
tachment points (Item e).
•
Fig. 27: Note that the marking arrows are op-
posite each other.
•
Fig. 28: Before you can close the grass bas-
ket you have to open it fully so that it latches
completely into the attachment points.
•
Fig. 29: Lock the grass basket by exerting
slight pressure on the rear handle.
Anl_GE_TM_102_BS_SPK7.indb 25 Anl_GE_TM_102_BS_SPK7.indb 25
GB
6. Operation
Note:
For detailed information on starting the engine, re-
fer to the enclosed manual from Briggs & Stratton.
Important.
The engine does not come with oil in it. Therefore,
be sure to add oil before starting the engine for
the fi rst time. You will also need to fi ll in petrol, as
this is also not supplied upon delivery.
Whenever you need to perform any adjustment
and/or repair work on your lawn mower, wait until
the blade has come to a complete stop. Always
switch off the engine before carrying out any ad-
justments, maintenance or repairs.
Warning: Never use more than one safety petrol
can. Do not smoke when refueling. Switch off the
engine before refueling and allow the engine to
cool down for a few minutes.
Safety switch
To prevent injuries from improper use, the lawn
mower is equipped with various safety devices.
To be able to start the engine, the following condi-
tions must be met:
•
Gear position → neutral
•
The mower unit must be switched off.
•
The operator must be sat on the seat.
•
The locking brake must be applied.
The engine cuts automatically whenever the ope-
rator leaves the seat.
Each time before use, check the tire pressure
and oil level.
Speed lever (Fig. 30)
Move the throttle lever (Item 14) in order to incre-
ase or decrease the engine speed. For optimum
mowing results we recommend that the throttle
lever should be set to the "Hare" position.
Tortoise = Slow
Hare = Fast
" " = Choke (enables a quick cold start)
Lights (Fig. 30):
Vehicle lights ON/OFF (Item 15).
Note: The lights only work if the ignition lock is in
the "ON" position.
- 25 -
02.08.12 10:21 02.08.12 10:21