Operation As Metal Saw; Transport; Replacing The Power Cable; Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL RT-XM 305 U Mode D'emploi D'origine

Anleitung_RT_XM_305_U_SPK7:_
GB

8. Operation as metal saw

Important. Wear gloves (risk of injury) and
suitable safety goggles.
You can make crosscuts with and without miter in
the angle ranges listed in section 7.) When
working with metal, you can only make crosscuts
due to risk of kick-back. In this case the drag
guide (24) must be fixed with the locking screw.
Before using the equipment, sweep any small
metal chips away from the machine to protect
yourself against injury. Always clamp the
workpiece with the vertical clamping device (8)
and the horizontal clamping device (21).
Press the ON/OFF switch (2). Wait until the saw
blade reaches full speed before making a cut.
Press the release lever (3). With the drag guide
(24) fixed in place, use the handle (1) to move the
machine head (4) downwards steadily, quickly
and exerting slight pressure until the workpiece is
completely cut through.
When the cutting operation is completed, move
the machine head (4) back to its upper (home)
position and release the ON/OFF button (2).
Let the saw blade run to a complete stop before
removing the workpiece.
Important: The integral resetting springs will
automatically lift the machine head. Do not simply
let go of the handle (1) after cutting but allow the
machine head (4) to rise slowly, applying slight
counterpressure as it does so.
9. Transport (Fig. 1-3)
Retighten the locking grip (14) to secure the
turntable (17) in place.
Activate the release lever (3), press the machine
head (4) downwards and secure with the
fastening bolt (27). The saw is now locked in its
bottom position.
Fix the saw's drag function with the locking screw
for the drag guide (25) in the rear position.
Carry the machine on the fixed saw table (18), or
if the saw is mounted to the base frame, on the
relevant trough handles on the base frame.
To set up the equipment again, proceed as
described in section 6.2.

10. Replacing the power cable

If the power cable for this equipment is damaged, it
must be replaced by the manufacturer or its after-
sales service or similarly trained personnel to avoid
26
22.10.2009 15:30 Uhr Seite 26
danger.
11. Cleaning, maintenance and
ordering of spare parts
Always pull out the mains power plug before starting
any cleaning work.
11.1 Cleaning
Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
down with compressed air at low pressure.
We recommend that you clean the equipment
immediately after you use it.
Clean the appliance regularly with a damp cloth
and some soft soap. Do not use cleaning agents
or solvents; these may be aggressive to the
plastic parts in the appliance. Ensure that no
water can get into the interior of the equipment.
11.2 Carbon brushes
In case of excessive sparking, have the carbon
brushes checked only by a qualified electrician.
Important. The carbon brushes should not be
replaced by anyone but a qualified electrician.
11.3 Servicing
There are no parts inside the equipment which
require additional maintenance.
11.4 Ordering replacement parts:
Please provide the following information on all orders
for spare parts:
Model/type of the equipment
Article number of the equipment
ID number of the equipment
Spare part number of the required spare part
For our latest prices and information please go to
www.isc-gmbh.info

12. Disposal and recycling

The equipment is supplied in packaging to prevent it
from being damaged in transit. The raw materials in
this packaging can be reused or recycled.
The equipment and its accessories are made of
various types of material, such as metal and plastic.
Defective components must be disposed of as
special waste. Ask your dealer or your local council.