Operation As Wood/Plastics Saw - EINHELL RT-XM 305 U Mode D'emploi D'origine

Anleitung_RT_XM_305_U_SPK7:_
GB
as shown in Figures 18 - 19.
8. Insert the two base frame parts in such a way that
the bottom and top cross struts (E, F) are
positioned in the relevant openings on the side
part (B) and the cross strut (C) (Figure 20).
9. Screw the bottom cross struts (E) to the other part
of the base frame (Figure 21/1) as described
under 5.
10. Screw the top cross struts (F) to the other part of
the base frame (Figure 21/2) as described under
6.
11. Pull the four rubber stoppers (32) from the bottom
side of the saw (Figure 22).
12. Place the saw onto the base frame so that the
openings in which the rubber stoppers (32) were
held are in line with the four openings on the top
side of the saw mounts (J). Then insert the four
screws (M) through the feet from the top and
screw the saw onto the base frame (Fig. 23 – 24).
6.4 Precision adjustment of the stop for crosscut
90° (Fig. 1, 25/-27)
Fasten the turntable (17) in 0° position.
Undo the locking screw (22) and move the
machine head (4) all the way to the right using the
handle (1).
Place the 90° angular stop (a) between the blade
(7) and the turntable (17).
Adjust the adjustment screw (38) until the angle
between the blade (7) and the turntable (17)
equals 90°.
Finally, check the position of the pointer (20) on
the scale (19). If necessary, release the pointer
(20) with a crosstip screwdriver, move to the 0°
position of the scale (19) and retighten the
holding screw.
No stop angle included.
6.5 Precision adjustment of the stop for miter cut
45° (Fig. 1, 25, 28-29)
Fasten the turntable (17) in 0° position.
Undo the locking screw (22) and move the
machine head (4) all the way to the left using the
handle (1), until it coincides at 45°.
Place the 45° stop angle (b) between the blade
(7) and the turntable (17).
Adjust the adjustment screw (37) so that the
angle between the blade (7) and the turntable
(17) equals exactly 45°.
No stop angle included.
24
22.10.2009 15:30 Uhr Seite 24

7. Operation as wood/plastics saw

7.1 Cross cut 90° and turntable 0° (Fig. 1-3, 30)
For cutting widths up to approx. 100 mm it is possible
to fix the saw's drag function with the locking screw
for drag guide (25) in rear position. If the cutting width
exceeds 100 mm you must ensure that the locking
screw for drag guide (25) is slackened and that the
machine head (4) can be moved.
Move the machine head (4) to its upper position.
Use the handle (1) to push back the machine
head (4) and fix it in this position if required
(dependent on the cutting width).
Place the piece of wood to be cut at the stop rail
(11) and on the turntable (17).
Lock the material with the clamping device (8) on
the fixed saw table (18) to prevent the material
from moving during the cutting operation.
Push down the release lever (3) to release the
machine head (4).
Press the ON/OFF switch (2) to start the motor.
With the drag guide (24) fixed in place: Use the
handle (1) to move the machine head (4) steadily
and with light pressure downwards until the saw
blade (7) has completely cut through the
workpiece.
With the drag guide (24) not fixed in place: Pull
the machine head (4) all the way to the front and
then use the handle (1) to move it downwards
steadily and with light pressure. Now push the
machine head (4) slowly and steadily to the very
back until the saw blade (7) has completely cut
through the workpiece.
When the cutting operation is completed, move
the machine head (4) back to its upper (home)
position and release the ON/OFF button (2).
Important. The integral resetting springs will
automatically lift the machine head. Do not simply let
go of the handle (1) after cutting, but allow the
machine head (4) to rise slowly, applying slight
counterpressure as it does so.
7.2 Cross cut 90° and turntable -52°...+60°
(Fig. 1-3, 31)
The crosscut saw can be used to make crosscuts of
0°- 52° to the left and 0° - 60° to the right in relation to
the stop rail.
Release the turntable (17) by slackening the
locking grip (14).
Press the latched position lever (13), turn the
turntable (17) and scale pointer (15) to the
desired angular setting on the dial (16) and lock
into place with the locking grip (14). The saw has
locking positions at angles of - -45°, -30°, -22.5°, -
15°, 0°, 15°, 22.5°, 30°, 45° and 60°, at which you
can engage latched position lever.