Current Dispenser; Key Function; Assistance Menu; Alarm List - Comestero Group SimplyCoin Mode D'emploi

_________________________________________________________________________________
– Coins:
COIN
CONFIGURATOR
In this function the values of the 8 coins accepted
by the electronic validator are set. For a correct
setting, set this function taking the programming
label of the coin box as a reference (RM5
Binary).
5 1.00 6 2.00
7 0.00 8 0.00
1 0.05 2 0.10
3 0.20 4 0.50
Chann. N. Coin value
– Banknotes:
BANKNOTE
CONFIGURATOR
In this function the values of the 4 banknotes
accepted by the reader are set. For a correct
setting, set this function taking the programming
label of the reader as a reference (NV5 Parallel).
1 5.00 2 10.0
3 20.00 4 50.00
Chann. N. Banknote value

6.5.3 Current dispenser

CURRENT DISPENSER
CONFIGURATION
In this section it is necessary to set the number
and contents of the hoppers so that the machine
can manage the dispensers and carry out the
change/accounting operation.
No1 : COINS
No2 : CONFIGURATION
By configuring Coins or Tokens the relevant
setting will be defined allowing to pilot the
Hopper Mod. MK4 produced by Coin Control
or MK2 produced by Suzo.

6.5.4 Key function

KEY FUNCTION
CONFIGURATION
In this function it is possible to select the
operating mode of the two external keys
according to the different requirements.
If the "SELECT DISPENSING" mode is
selected, key A (left) will be used to choose the
type of dispensing to use based on the
programmed change tables, while key B (right)
will be used to dispense the pieces contained in
the Hoppers.
KEY FUNCTION
SELECT DISPENSING
If "DISPENSE <A> DISPENSE <B>"mode is
selected, key A will be used to dispense the
pieces contained in HOPPER1, while key B will
be used to dispense the pieces contained in
HOPPER2.
KEY FUNCTION
DISPENSE A DISPENSE B

6.6 Assistance menu

ASSISTANCE TECHINCIAN
MANAGEMENT
The Assistance menu includes the diagnostic
functions of the machine. To access this menu
just press "+" and "OK" at the same time for a
few seconds, then move with "+" until the word
"ASSISTANCE" is displayed. Then confirm
with "OK".
The diagnostic functions are usually employed
by the Technicians to check the correct operation
of the machine, as the last type of error occurred
is recorded should the machine not work
35
_________________________________________________________________________________
correctly. It is therefore advisable to contact the
After-Sale Manager who will help you in the
check operations. The functions that can be
programmed in this menu are explained below.
ASSISTANCE:

ALARM LIST

EMPTYING

RESET

LOAD DEFAULT

EXIT
6.6.1 Alarm list
ALARM LIST
ASSISTANCE
The Change Machine can diagnose different
types of anomalies that are recorded in memory.
This function records the last anomaly found
out.
ALARM LIST:
-NO ALARM
-DISPENSING WITHOUT CONTROL
-COIN UNDER SENSOR (hopper)
-FAULTY COIN SENSOR (hopper)
6.6.2 Emptying
EMPTYING
ASSISTANCE
This function is useful when you want to carry
out the complete dispenser emptying (Hopper).
EMPTYING
HOPPER 1
6.6.3 Reset
RESET
ASSISTANCE
The reset function enables to reset the alarm
displayed in the ALARM LIST function.
RESET ALARMS?
YES NO
6.6.4 Load default
From version 1.33 onwards, a new function
called "LOAD DEFAULT" has been included in
the ASSISTANCE menu.
LOAD DEFAULT
ASSISTANCE
LOAD DEFAULT?
SI NO
If this function is confirmed, the board will reset
and set a standard programming. This
programming will require the setting of all coins
having values ranging between 0.05€ and 2.00€
and of all banknotes between 5.00€ and 20.00€.
Credit will be set at a value of 0,50€.

6.7 Display signals

TOKEN
DISPENSER 1.00€
Normal operating condition.
OUT OF ORDER
CALL TECHNICIAN
This message indicates that the configuration and
accounting data are corrupt and it is necessary to
set accounting to zero and to reconfigure the
board.
OUT OF ORDER
TO BE REPROGRAMMED
This message indicates that the program is
corrupt and the board shall be programmed at
Comestero.
36