Publicité
NOTE:
The appliance supports 2.4 GHz Wi-Fi networks only. Check your network frequency, contact your Internet provider or refer to your
wireless router manual.
•
If the appliance is having trouble connecting to the Wi-Fi network, it may be too far from the router.
•
The Wi-Fi connection may be interrupted because of the home network and/or surrounding wireless environment.
•
The Wi-Fi connection may not work depending on the Internet provider.
Make sure the appliance is plugged into a power outlet and placed near a Wi-Fi router. It is important that the Wi-Fi network the appli-
ance will be connected to is a 2.4 GHZ network.
Enable bluetooth and WiFi on your phone or tablet. Use your phone to search "Smart life" in Google play or App store to download and
install the app. Follow the steps in the app that indicate how the appliance gets connected.
If no Wi-Fi network available: the appliance can be operated manually on its control display.
First, plug in the main cable to the wall socket and click the switch at the right upper side of the appliance.
F. TROUBLESHOOTING
Problem
The appliance does
not heat up
The room does not
reach the desired
temperature
The radiator does not
operate
The radiator stains the
walls
Blocked buttons
G. MAINTENANCE
The floor should be kept clean to avoid stains on the wall due to a convection effect at the appliance.
Always make sure the radiator openings are completely clean and are fully open. Check this weekly and clean if openings are not com-
pletely open
At the beginning of the heating season, the underside of the appliance should be vacuumed. This is important because dust can accumu-
late in the lower grille, this can affect the natural convection airflow and cause stains on the wall.
The appliance can be cleaned with a damp cloth or Soapy water.
H. WARRANTY
This section of the manual outlines the terms and conditions of the guarantee for the appliance you have pur-
chased. Scan the QR-code below that directs you to the full information and your rights regarding the product
warranty. Please read the information specified on the weblink carefully. If there is no warranty support for your
country, then please contact your local dealer.
To prevent unnecessary expense, we recommend that you always first carefully consult the instructions for use.
Please call the after sales number if these instructions do not provide a solution.
Should the intructions not be sufficient, see the back of the manual for your country's after-sales number.
Probable cause
The appliance is in energy-
saving mode
Incorrect setting of the set tem-
perature
Improper sizing
Excessive height
Input and output grids are
obstructed
Set temperature below room
temperature
Control panel switch and protec-
tion down
Switch is off
Program is OFF
Radiator located at a very low
height
Dust accumulation in the lower
grid.
Type of painting on the wall
No response from operating
buttons
Solution
Due to the thermal inertia, the appliance transfers heat to the room;
should you need more temperature, increase the appliance temperature.
Check the set temperature on the display to verify it is the desired tempe-
rature
The power is not the adequate for the place in which it has been installed
Make sure the system is installed at the recommended height or rise set tempe-
rature to compensate probe reading
Do not place anything on top of the radiator and do not install it inside a
hole made in the septum
Rise the radiator's set temperature until it is 1 degree above the room tem-
perature
Check that the automatic limiter in the installation is not down. If it is down
put it up.
Make sure the installation is correct and that there are independent lines for the
heating system with a 2.5 mm2 cable gauge and a maximum power of 3500 w
Set the switch in position I.
Check that the set program is the chosen one or set the one you desire.
The minimum height from the floor to the radiator's lower part must be at
least 25 cm.
Vacuum it. The vacuuming should be done at the beginning of each hea-
ting season.
Paints with a high content in rutile are likely to darken
Press buttons MODE and
simultaneously for 3 seconds
4
17
Publicité
