Johnson AURUM R290 M Serie Guide D'utilisation page 103

For serviceman
For serviceman
1 DHW setting
2 Cooling setting
3 Heating setting
4 Auto mode setting
5 Temp. type setting
6 Room thermostat setting
7 Other heating source
8 Service call
9 Restore factory setting
10 Test run
11 Special function
12 Auto restart
13 Power input limitation
14 Input define
15 Cascade setting
16 HMI address setting
17 Common setting
18 Clear energy data
19 Intelligent function settings
20 C2 fault restore
There are some items that are invisible if the function is disabled or unavailable.
1 DHW setting
1.1 DHW mode
1.2 Disinfect
1.3 DHW priority
1.4 Pump_D
1.5 DHW priority time set
1.6 dT5_ON
1.7 dT1S5
1.8 T4DHWMAX
1.9 T4DHWMIN
1.10 T5S_Disinfect
1.11 t_DI_HIGHTEMP.
1.12 t_DI_MAX
1.13 t_DHWHP_Restrict
1.14 t_DHWHP_MAX
1.15 Pump_D timer
1.16 Pump_D running time
1.17 Pump_D disinfect
2 Cooling setting
2.1 Cooling mode
2.2 t_T4_Fresh_C
2.3 T4CMAX
2.4 T4CMIN
2.5 dT1SC
2.6 dTSC
2.7 Zone 1 C-emission
2.8 Zone 2 C-emission
3 Heating setting
3.1 Heating mode
3.2 t_T4_Fresh_H
3.3 T4HMAX
3.4 T4HMIN
3.5 dT1SH
3.6 dTSH
3.7 Zone 1 H-emission
3.8 Zone 2 H-emission
3.9 Force defrost
4 Auto mode setting
4.1 T4AUTOCMIN
4.2 T4AUTOHMAX
5 Temp. type setting
5.1 Water flow temp.
5.2 Room temp.
5.3 Double zone
6 Room thermostat setting
6.1 Room thermostat
6.2 Mode set priority
16 HMI address setting
16.1 HMI address for BMS
16.2 Stop BIT
17 Common setting
17.1 t_Delay pump
17.2 t1_Antilock pump
17.3 t2_Antilock pump run
17.4 t1_Antilock SV
17.5 t2_Antilock SV run
17.6 Ta_adj.
17.7 Pump_I silent output
17.8 Energy metering
17.9 Pump_O
17.10 Glycol
17.11 Glycol concentration
46
7 Other heating source
7.1 IBH function
7.2 dT1_IBH_ON
7.3 t_IBH_Delay
7.4 T4_IBH_ON
7.5 P_IBH1
7.6 P_IBH2
7.7 AHS function
7.8 AHS_Pump_I Control
7.9 dT1_AHS_ON
7.10 t_AHS_Delay
7.11 T4_AHS_ON
7.12 EnSwitchPDC
7.13 GAS_COST
7.14 ELE_COST
7.15 MAX_SETHEATER
7.16 MIN_SETHEATER
7.17 MAX_SIGHEATER
7.18 MIN_SIGHEATER
7.19 TBH function
7.20 dT5_TBH_OFF
7.21 t_TBH_Delay
7.22 T4_TBH_ON
7.23 P_TBH
7.24 Solar function
7.25 Solar control
7.26 Deltasol
8 Service call
Phone number
Mobile number
9 Restore factory settings
10 Test run
11 Special function
11.1 Preheating for floor
11.2 Floor drying up
12 Auto restart
12.1 Auto restart cooling/
heating mode
12.2 Auto restart DHW mode
13 Power input limitation
13.1 Power input limitation
14 Input define
14.1 M1M2
14.2 Smart grid
14.3 T1T2
14.4 Tbt
14.5 P_X PORT
15 Cascade setting
15.1 PER_START
15.2 TIME_ADJUST
18 Clear energy data
19 Intelligent function settings
19.1 Energy correction
19.2 Sensor backup setting
20 C2 fault restore
V.1