Publicité
the stand is stable against the vehicle before removing grip from
rear leg support bar.
c. Move to the handle side of the saw, grasp handles and move saw
to desired location.
a. With the saw in the work
position, unhook elastic strap
end from bottom over side
table water tray and rotate
strap over side table to
engage storage screw at top
of side water tray.
b. Loosen side table knob by
rotating COUNTER-CLOCKWISE until fastener is disengaged
from main table. Remove side water tray and side table by
pulling assembly from the side of the main table.
pivoting towards rear water tray. Grasp sides of rear water
tray and slightly lift, then pull back to remove rear water tray
from water tank.
a. With the saw in the transport
position, place the side water
tray and extension table
assembly between the upper
front leg support bar and
water tank. Disengage the
elastic strap and place around
the outside of the upper front
leg support bar and re-attach.
b. With the rear water tray splash
the water tank, unhook the left
elastic strap from the stand
and re-attach to mounting
screw on left side of rear
water tray. Repeat process
for right side.
Ensure that the drain plug at the back of the water tank is secure
indicated in the tank.
Unplug the saw, place a bucket under the drainage plug and remove
the plug to drain the dirty water into the bucket.
Rinse the machine properly.
Dispose of the dirty water in accordance with local regulations.
Replace with clean water.
incorporated safety lock function. Removal of safety key will prevent
• With the safety key inserted in the switch, lift the switch to
power on saw.
•
• With the saw SWITCHED OFF, remove the safety key from the
switch and keep it in a safe place.
To reduce the risk of accidental start-up, always ensure
that the switch is in the OFF position before plugging the tool in to the
power source.
- 8 -
(Picture 19)
Ensure that the part to be cut is not in contact with the
blade before operating the switch to start the cutter. Otherwise, the
part to be cut could move back towards the user and cause serious
personal injuries.
The water pump operation can be set using the switch next to the
a. With the pump switch in position I, the pump will start when the
b. With the pump switch in position II, the pump is always on to keep
for operation with dry cut blades.
Your saw is equipped with a new cooling system that improves cutting
blade cooling while reducing water splashing at the same time. For
be adjusted to the thickness of the material to be cut.
a. Place the tile to be cut on the sliding table.
b. Adjust the position of the C3 Python system by pressing the lever
located at the front of the cutting blade cover, and move the
cut, without touching it.
(Picture 22)
Your saw's cutting head can move vertically to make square cuts in the
center of the tile, for electrical sockets or inspection boxes.
a. Hold the cutting head by the handle and disengage the locking pin
located behind the motor.
b. While holding the head by the handle, loosen the locking knob in
the COUNTER-CLOCKWISE direction.
c. While holding the cutting head at the desired height, turn the
reach at least 5 mm below the surface of the table.
To lock the cutting head back in its normal work position, slide
a. Loosen the limiter's locking lever.
b. Release the cutting head and move it to the desired maximum
cutting depth.
The travel limiter is automatically adjusted to the desired
maximum depth. Before adjusting, ensure that travel limiter is clean
and can move freely.
c. While holding the cutting head at the desired maximum cutting
depth, tighten the limiter's locking lever.
(Picture 24)
Your saw is equipped with a laser guide that indicates the cutting line
through which the blade will pass as the sliding table moves forward.
The laser is used to assist with aligning specialty cuts such as unique
diagonal cuts, plunge cuts, and L-cuts. The laser line can be used to
position tile to the desired cutting line.
• To turn on the laser guide, press the button on the right
of the handle.
Laser will provide a consistent line to guide specialty cuts.
If laser line needs adjustment, consult the adjustment section of
this manual.
recommended for use in lower light and shade.
(Picture 25)
a. Move the angle guide to the width of the desired cut and secure
the position with the locking knob.
angle for angle cuts. Secure the desired angle with the locking knob.
(Picture 20)
(Picture 21)
(Picture 23)
Publicité
