Télécharger Imprimer la page

EINHELL TE-COL 18/27 Li Instructions D'origine page 16

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 22
5.2 Charging the lithium-ion battery pack
(Fig. 4/5)
1. Remove the battery pack from the mount by
pressing the pushlock button (c) downwards.
2. Check that your mains voltage is the same as
that marked on the rating plate. Insert the po-
wer plug of the charger into the power socket.
The green LED will begin to blink.
3. Push the battery pack onto the battery char-
ger.
In the section entitled „Charger indicator" you will
fi nd a table with an explanation of the LED display
on the charger.
5.3 Battery capacity indicator (Fig. 6)
Press the button for the battery capacity indicator
(A). The battery capacity indicator (B) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
If the battery pack fails to charge, check for the
following:
Is there voltage at the power socket?
Is there good contact at the charger's char-
ging contacts?
If the battery pack still fails to charge, please send
the charger
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
Anl_TE_COL_18_27_Li_SPK13.indb 16
Anl_TE_COL_18_27_Li_SPK13.indb 16
GB
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
5.4 Filling the cool box
CAUTION – Risk of damage to health!
To prevent food contamination, follow the instruc-
tions below:
Leaving the lid open for prolonged periods
can lead the temperature in the compart-
ments of the device to rise considerably.
Regularly clean any surfaces that may come
into contact with food.
Store raw meat and fish in suitable containers
so that they do not come into contact with or
drip on other food items.
If the refrigerator/freezer is to remain empty
for a long time, switch off the device, defrost,
clean and dry it, and leave the lid open to pre-
vent mold from growing.
Place the cool box on a sturdy surface (e.g. the
fl oor). Move the carry-handle (Fig. 1 / Item 5) for-
ward and open the lid (Fig. 1 / Item 6). To keep the
lid open while fi lling the cool box with food/drinks,
the carry-handle can be used to brace the lid (Fig.
7). The mesh divider (Fig. 7 / Item E) can be used
to keep diff erent food items separated. Close the
lid and move the carry-handle backward.
The lid can only be opened if the carry-handle is
in the forward position.
5.5 Transporting the cool box
You can use the shoulder strap (Fig. 1 / Item 1) or
the carry-handle (Fig. 1 / Item 5) to transport the
cool box.
5.6 Bottle opener
On the front side of the cool box there is a bottle
opener (Fig. 1 / Item 4) for opening bottles with
bottle caps.
5.7 Outside pockets
The pockets on the front and left sides provide
additional storage space, used to hold batteries,
for example.
- 16 -
03.12.2024 11:28:27
03.12.2024 11:28:27

Publicité

loading

Ce manuel est également adapté pour:

20.484.20