Nolan N40 FULL Sécurité Et Instructions D'utilisation page 9

Maintenance and Cleaning
- Remove the PINLOCK
the soap under running water.
- Dry the inner visor with dry and warm air without wiping it.
- To keep the features of the inner visor in good conditions over time, let the helmet dry in a ventilated and dry place with the
visor open after use. Keep it away from heat sources and store it in a place away from direct light.
- Do not use solvents or chemical products.
SIDE PLATES
When the helmet N40 FULL is configured without the visor the side plates must be assembled in its place.
11 Side Plates Assembly
To assemble the side plates first remove the lateral latches and (if assembled) the peak and the visor (see instructions above).
11.1 Place the left side plate on the corresponding side mechanism centring its hole on the mechanism and its teeth (Fig. 16).
11.2 If you wish to assemble the peak above the plates see the relevant installation instructions.
11.3 Assemble the left lateral latch as indicated in the instructions above.
11.4 Follow the same steps on the right side of the helmet.
12 Side Plates Disassembly
To disassemble the side plates first remove the lateral latches and (if assembled) the peak (see instructions above).
Then remove the plates from the side mechanisms.
Next, reassemble the visor and then the peak (if any) as explained in the previous instructions.
WARNING
- When using the helmet in a configuration without the visor, always assemble the lateral latches and the side plates.
- Do not use the helmet if the plates and the lateral latches have not been assembled properly.
- If the peak is assembled over the plates the proper operation as described previously.
- Do not remove the side mechanisms from the shell.
- Should any of the side mechanisms fail or be damaged, please refer to a Nolan authorized dealer.
VISION PROTECTION SYSTEM (VPS)
The exclusive inner VISION PROTECTION SYSTEM (VPS) is a LEXAN™
resistant/fog-resistant treatment. Very simple and practical to use. Just lower to activate it or lift to remove it from the field of vision.
It is useful in all sorts of situations, both on long journeys out of town and shorter town trips.
(*) LEXAN is a trademark of SABIC.
Maintenance and Cleaning
- Remove the PINLOCK
the soap under running water.
- Dry the inner visor with dry and warm air without wiping it.
- To keep the features of the inner visor in good conditions over time, let the helmet dry in a ventilated and dry place with the
visor open after use. Keep it away from heat sources and store it in a place away from direct light.
- Do not use solvents or chemical products.
SIDE PLATES
When the helmet N40 FULL is configured without the visor the side plates must be assembled in its place.
11 Side Plates Assembly
To assemble the side plates first remove the lateral latches and (if assembled) the peak and the visor (see instructions above).
11.1 Place the left side plate on the corresponding side mechanism centring its hole on the mechanism and its teeth (Fig. 16).
11.2 If you wish to assemble the peak above the plates see the relevant installation instructions.
11.3 Assemble the left lateral latch as indicated in the instructions above.
11.4 Follow the same steps on the right side of the helmet.
12 Side Plates Disassembly
To disassemble the side plates first remove the lateral latches and (if assembled) the peak (see instructions above).
Then remove the plates from the side mechanisms.
Next, reassemble the visor and then the peak (if any) as explained in the previous instructions.
WARNING
- When using the helmet in a configuration without the visor, always assemble the lateral latches and the side plates.
- Do not use the helmet if the plates and the lateral latches have not been assembled properly.
- If the peak is assembled over the plates the proper operation as described previously.
- Do not remove the side mechanisms from the shell.
- Should any of the side mechanisms fail or be damaged, please refer to a Nolan authorized dealer.
VISION PROTECTION SYSTEM (VPS)
The exclusive inner VISION PROTECTION SYSTEM (VPS) is a LEXAN™
resistant/fog-resistant treatment. Very simple and practical to use. Just lower to activate it or lift to remove it from the field of vision.
It is useful in all sorts of situations, both on long journeys out of town and shorter town trips.
(*) LEXAN is a trademark of SABIC.
® inner visor from the visor. Using a damp and soft cloth, gently clean it with neutral liquid soap. Remove
® inner visor from the visor. Using a damp and soft cloth, gently clean it with neutral liquid soap. Remove
(*) polycarbonate moulded sunscreen with scratch-
9
(*) polycarbonate moulded sunscreen with scratch-
9