Nolan N40 FULL Sécurité Et Instructions D'utilisation page 11

- Always make sure that the VPS is clean and that it is operating properly in order to avoid scratches and/or anomalous wear
on it every time it is activated.
- As for VPS and visor maintenance and cleaning operations, please refer to the appropriate section in the helmet user's manual.
- The VPS scratch-resistant/fog-resistant treatment highly reduces fogging. Protracted periods of adverse weather and/or envi-
ronmental conditions might cause fogging and/or formation of condensation on the VPS, which entails a reduction of visibili-
ty and/or sharpness of vision: in this case, deactivate the VPS.
- In case of rain, the direct contact of raindrops with the scratch-resistant/fog-resistant treated VPS quickly reduces sharpness
of vision, thus causing scarce visibility: in this case, deactivate the VPS.
- The special VPS fog-resistant treatment is usually sensitive to high temperatures or heat sources. In this case, contaminations
caused by contact with other materials might occur. These contaminations will cause marks and stains to develop. In these
cases (e.g. when the helmet is kept in the top case on hot days), it is recommended to make sure the visor is not touching
other materials.
13 VPS Disassembly
To remove the sun screen from the helmet, open the visor completely and lower the VPS by rotating the side slider completely
upwards (Fig. 17 B).
Hold the left lateral part of the sun screen and pull it toward the outside of the helmet (Fig. 18).
Repeat the same operation on the right side of the helmet.
14 VPS Assembly
To assemble the sun screen on the helmet, open the visor completely and push the side slider completely upwards (Fig. 17 B).
Insert the sun screen left end into the left side guide until the grip pawl is hooked in shell housing (Fig. 18).
Repeat the same operation on the right side of the helmet.
WARNING
- Make sure the VPS operates correctly by moving the left side slider towards the bottom (Fig. 17 A) and the top side of the hel-
met (Fig. 17 B) until you hear the clicks meaning that it enters the relative positions. If necessary, repeat the above-mentioned
steps.
- If the VPS opening/closing mechanisms are not working properly or if such mechanisms get damaged, please contact a Nolan
authorized dealer.
- Do not use the helmet if the VPS has not been assembled properly.
- Since the VPS does not assure you the same protection as the one provided by the visor, it has to be used only when the hel-
met visor is lowered.
- Always make sure that the VPS is clean and that it is operating properly in order to avoid scratches and/or anomalous wear
on it every time it is activated.
- As for VPS and visor maintenance and cleaning operations, please refer to the appropriate section in the helmet user's manual.
- The VPS scratch-resistant/fog-resistant treatment highly reduces fogging. Protracted periods of adverse weather and/or envi-
ronmental conditions might cause fogging and/or formation of condensation on the VPS, which entails a reduction of visibili-
ty and/or sharpness of vision: in this case, deactivate the VPS.
- In case of rain, the direct contact of raindrops with the scratch-resistant/fog-resistant treated VPS quickly reduces sharpness
of vision, thus causing scarce visibility: in this case, deactivate the VPS.
- The special VPS fog-resistant treatment is usually sensitive to high temperatures or heat sources. In this case, contaminations
caused by contact with other materials might occur. These contaminations will cause marks and stains to develop. In these
cases (e.g. when the helmet is kept in the top case on hot days), it is recommended to make sure the visor is not touching
other materials.
13 VPS Disassembly
To remove the sun screen from the helmet, open the visor completely and lower the VPS by rotating the side slider completely
upwards (Fig. 17 B).
Hold the left lateral part of the sun screen and pull it toward the outside of the helmet (Fig. 18).
Repeat the same operation on the right side of the helmet.
14 VPS Assembly
To assemble the sun screen on the helmet, open the visor completely and push the side slider completely upwards (Fig. 17 B).
Insert the sun screen left end into the left side guide until the grip pawl is hooked in shell housing (Fig. 18).
Repeat the same operation on the right side of the helmet.
WARNING
- Make sure the VPS operates correctly by moving the left side slider towards the bottom (Fig. 17 A) and the top side of the hel-
met (Fig. 17 B) until you hear the clicks meaning that it enters the relative positions. If necessary, repeat the above-mentioned
steps.
- If the VPS opening/closing mechanisms are not working properly or if such mechanisms get damaged, please contact a Nolan
authorized dealer.
- Do not use the helmet if the VPS has not been assembled properly.
- Since the VPS does not assure you the same protection as the one provided by the visor, it has to be used only when the hel-
met visor is lowered.
11
11