Nolan N40 FULL Sécurité Et Instructions D'utilisation page 13

- Never use the helmet before completely and correctly reassembling its inner comfort padding.
- Delicately hand-wash in lukewarm water (max. 30° C) and neutral soap.
- Rinse with cold water and allow drying at room temperature, away from direct sunlight.
- Never machine-wash the inner comfort padding.
- The inner polystyrene is an easily deformable material. It is apt to change or get partially destroyed to help absorb shocks.
- Do not modify or alter the helmet's internal polystyrene components in any way.
- Clean the inner components with a damp cloth only and allow it to dry at room temperature away from direct sunlight.
- Never use tools or equipment of any sort to carry out the steps described above.
WIND PROTECTOR
(Available as standard or accessory/spare part).
This accessory allows improved helmet performance under certain conditions of use. The Wind Protector reduces unpleasant infil-
trations of air under the chin.
See Fig. 24 for assembly and disassembly.
VENTILATION SYSTEM
The ventilation system of the N40 FULL helmet consists of:
Front Air Intake: the innovative AIRBOOSTER TECHNOLOGY channels the air coming from the front air intake by directing it in the
top area of the rider's head without any dispersion. The front air intake (Fig. 25) can be completely or partially opened depending on
whether its slider is pulled completely backwards (A). To close the front air intake, pull the above mentioned slider completely for-
ward (B).
Chin Guard Air Intake: allows ventilation in the mouth and visor area. See Fig. 26 for how to open and close it.
Rear Extractors: are integrated in a rear spoiler and allow warm and stale air to flow out ensuring an optimum comfort inside the
helmet (Fig. 27).
N-COM - NOLAN COMMUNICATION SYSTEM PRE-SETTING
Your Nolan helmet is factory-preset to be equipped with the N-Com communication system During the communication system
installation (see the specific instructions contained in the N-Com kit), it will be necessary to remove the foam material fillers located
in the polystyrene cheek pads next to the N-Com earphones seats.
WARNING
- The above-mentioned fillers should only be removed if the helmet is used with an N-Com compatible system installed.
- Never use the helmet before completely and correctly reassembling its inner comfort padding.
- Delicately hand-wash in lukewarm water (max. 30° C) and neutral soap.
- Rinse with cold water and allow drying at room temperature, away from direct sunlight.
- Never machine-wash the inner comfort padding.
- The inner polystyrene is an easily deformable material. It is apt to change or get partially destroyed to help absorb shocks.
- Do not modify or alter the helmet's internal polystyrene components in any way.
- Clean the inner components with a damp cloth only and allow it to dry at room temperature away from direct sunlight.
- Never use tools or equipment of any sort to carry out the steps described above.
WIND PROTECTOR
(Available as standard or accessory/spare part).
This accessory allows improved helmet performance under certain conditions of use. The Wind Protector reduces unpleasant infil-
trations of air under the chin.
See Fig. 24 for assembly and disassembly.
VENTILATION SYSTEM
The ventilation system of the N40 FULL helmet consists of:
Front Air Intake: the innovative AIRBOOSTER TECHNOLOGY channels the air coming from the front air intake by directing it in the
top area of the rider's head without any dispersion. The front air intake (Fig. 25) can be completely or partially opened depending on
whether its slider is pulled completely backwards (A). To close the front air intake, pull the above mentioned slider completely for-
ward (B).
Chin Guard Air Intake: allows ventilation in the mouth and visor area. See Fig. 26 for how to open and close it.
Rear Extractors: are integrated in a rear spoiler and allow warm and stale air to flow out ensuring an optimum comfort inside the
helmet (Fig. 27).
N-COM - NOLAN COMMUNICATION SYSTEM PRE-SETTING
Your Nolan helmet is factory-preset to be equipped with the N-Com communication system During the communication system
installation (see the specific instructions contained in the N-Com kit), it will be necessary to remove the foam material fillers located
in the polystyrene cheek pads next to the N-Com earphones seats.
WARNING
- The above-mentioned fillers should only be removed if the helmet is used with an N-Com compatible system installed.
13
13