Grounding Instructions; Extension Cords - Delta BS150LS Manuel D'utilisation

gROUNDINg INSTRUCTIONS

This machine must be grounded while in use to protect the operator from electric shock.
1. All grounded, cord-connected machines:
In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to
reduce the risk of electric shock. This machine is equipped with an electric cord having an equipment-grounding
conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
Do not modify the plug provided - if it will not fit the outlet, have the proper outlet installed by a qualified electrician.
Improper connection of the equipment-grounding conduc-tor can result in risk of electric shock. The conductor
with insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding
conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-
grounding conductor to a live terminal.
Check with a qualified electrician or service personnel if the grounding instructions are not completely
understood, or if in doubt as to whether the machine is properly grounded.
Use only 3-wire extension cords that have 3-prong grounding type plugs and matching 3-conductor receptacles that
accept the machine's plug, as shown in Fig. A.
Repair or replace damaged or worn cord immediately.
2. grounded, cord-connected machines intended for use on a supply circuit having a nominal rating less
than 150 volts:
If the machine is intended for use on a circuit that has an outlet that looks like the one illustrated in Fig. A, the
machine will have a grounding plug that looks like the plug illustrated in Fig. A. A temporary adapter, which looks
like the adapter illustrated in Fig. B, may be used to connect this plug to a matching -conductor receptacle as
shown in Fig. B if a properly grounded outlet is not available. The temporary adapter should be used only until
a properly grounded outlet can be installed by a qualified electrician. The green-colored rigid ear, lug, and the
like, extending from the adapter must be connected to a permanent ground such as a properly grounded outlet
box. Whenever the adapter is used, it must be held in place with a metal screw.
NOTE: In Canada, the use of a temporary adapter is not permitted by the Canadian Electric Code.
In all cases, make certain that the receptacle in question is properly grounded. If you are not sure,
have a qualified electrician check the receptacle.
GROUNDED OUTLET BOX
CURRENT
CARRYING
PRONGS
GROUNDING BLADE
IS LONGEST OF THE 3 BLADES

EXTENSION CORDS

Use proper extension cords. Make sure
your extension cord is in good condition and is a 3-
wire extension cord which has a 3-prong grounding
type plug and matching receptacle which will accept
the machine's plug. When using an extension cord,
be sure to use one heavy enough to carry the current
of the machine. An undersized cord will cause a drop
in line voltage, resulting in loss of power and over-
heating. Fig. D-1 or D-2, shows the correct gauge to
use depending on the cord length. If in doubt, use
the next heavier gauge. The smaller the gauge num-
ber, the heavier the cord.
Fig. A
GROUNDED OUTLET BOX
GROUNDING MEANS
MINIMUM gAUgE EXTENSION CORD
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES
Ampere
Rating Volts
0-6 120
0-6 120
0-6 120
0-6 120
6-10 120
6-10 120
6-10 120
6-10 120
10-12 120
10-12 120
10-12 120
10-12 120
12-16 120
12-16 120
12-16 120
gREATER THAN 50 FEET NOT RECOMMENDED
6
ADAPTER
Fig. B
Total Length gauge of
of Cord in Feet Extension Cord
up to 25 18 AWg
25-50 16 AWg
50-100 16 AWg
100-150 14 AWg
up to 25 18 AWg
25-50 16 AWg
50-100 14 AWg
100-150 12 AWg
up to 25 16 AWg
25-50 16 AWg
50-100 14 AWg
100-150 12 AWg
up to 25 14 AWg
25-50 12 AWg
Fig. D