Additional Specific Safety Rules; Power Connections; Motor Specifications - Delta BS150LS Manuel D'utilisation

ADDITIONAL SPECIFIC SAFETY RULES

1. DO NOT OPERATE THIS MACHINE UNTIL it is
assembled and installed according to the instruc-
tions.
. OBTAIN ADVICE from your supervisor, instructor,
or another qualified person if you are not familiar
with the operation of this tool.
3. FOLLOW ALL WIRINg CODES and recommended
electrical connections.
USE THE gUARDS WHENEVER POSSIBLE. Check to
4.
see that they are in place, properly adjusted, secured,
and working correctly.
5. USE PROPER BLADE SIZE and type.
6. ADJUST THE UPPER BLADE gUIDE so that it is
about 1/8" above the workpiece.
PROPERLY ADJUST the blade tension, tracking,
7.
blade guides, and blade support bearings.
kEEP ARMS, HANDS, AND FINgERS away from
8.
the blade.
9. AVOID AWkWARD OPERATIONS and hand po-
sitions where a sudden slip could cause a hand to
move into the blade.
10. NEVER START THE MACHINE before clearing the
table of all objects (tools, scrap pieces, etc.).
11. NEVER START THE MACHINE with the workpiece
against the blade.
1. HOLD WORkPIECE FIRMLY against the table. DO
NOT attempt to saw a workpiece that does not have
a flat surface against the table.
13. HOLD WORkPIECE FIRMLY and feed into blade at
a moderate speed.
14. NEVER REACH UNDER THE TABLE while the ma-
chine is running.
SAVE THESE INSTRUCTIONS.
Refer to them often and use them to instruct others

POWER CONNECTIONS

A separate electrical circuit should be used for your machines. This circuit should not be less than #1 wire and should
be protected with a 0 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have
3-prong grounding type plugs and matching receptacle which will accept the machine's plug. Before connecting the
machine to the power line, make sure the switch (s) is in the "OFF" position and be sure that the electric current is of
the same characteristics as indicated on the machine. All line connections should make good contact. Running on low
voltage will damage the machine.
DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS.

MOTOR SPECIFICATIONS

Your machine is wired for 10 volt, 60 HZ alternating current. Before connecting the machine to the power source,
make sure the switch is in the "OFF" position.
Failure to follow these rules may result in serious personal injury.
15. TURN THE MACHINE "OFF" to back out of an un-
completed or jammed cut.
16. MAkE "RELIEF" CUTS prior to cutting long curves.
17. TURN THE MACHINE "OFF" and wait for the blade
to stop prior to cleaning the blade area, removing
debris near the blade, removing or securing work-
piece, or changing the angle of the table. A coasting
blade can be dangerous.
18. NEVER PERFORM LAYOUT, ASSEMBLY, or set-
up work on the table/work area when the machine is
running.
19. TURN THE MACHINE "OFF" AND DISCONNECT
THE MACHINE from the power source before in-
stalling or removing accessories, before adjusting or
changing set-ups, or when making repairs.
0. TURN THE MACHINE "OFF", disconnect the ma-
chine from the power source, and clean the table/
work area before leaving the machine. LOCk THE
SWITCH IN THE "OFF" POSITION to prevent unau-
thorized use.
1. ADDITIONAL INFORMATION regarding the safe
and proper operation of power tools (i.e. a safety
video) is available from the Power Tool Institute, 1300
Sumner Avenue, Cleveland, OH 44115-851 (www.
powertoolinstitute.com). Information is also avail-
able from the National Safety Council, 111 Spring
Lake Drive, Itasca, IL 60143-301. Please refer to
the American National Standards Institute ANSI 01.1
Safety Requirements for Woodworking Machines
and the U.S. Department of Labor OSHA 1910.13
Regulations.
5
.