Cleaning And Maintenance - incubato IN-7DDI Manuel D'utilisation

14
Model IN- IN- IN- IN- IN- IN- IN-
7 48 56 96 88 32 112
DDI DDI DDI DDI DDI DDI DDI
How One egg in each egg tray hole.
should
hen and
pigeon
eggs be
spaced.
How Leave one empty space (hole) between
should the eggs on the tray.
turkey and
duck eggs
be spaced.
How - Remove the egg tray and place the
should eggs on the net.
goose
eggs be
spaced
IN-7DDI model
1. Remove cover and lift egg tray.
2. Pour water into the groove around the white mesh as
(shown in the picture below).
ATTENTION: Do not pour water into the white mesh
as that may damage the device!
3. Attach cover.
4. Connect the device to a power source.
5. Select the required temperature: press the „SET" (6)
button. The „set" (3) diode will illuminate, indicating
that the device is in settings mode. Use „+" (5) and
„-" (4) buttons to select the temperature. Use the
„SET" (6) button to confirm. The „Work" (2) diode will
come on.
6. Wait for the device to warm up (approx. 10-20 min.).
7. Gently arrange the eggs on the tray.
8. Inspect the water level in the egg incubator regularly.
IN-48DDI, IN-96DDI, IN-112DDI models
1. Lift the cover, pour water into the egg incubator.
Make sure the drive mechanism does remains dry.
Close the cover.
2. Connect the device to a power source.
3. Use the On/Off (5) switch to turn the device on.
4. An alarm will sound. Disable the alarm by pressing
a button on the control panel.
5. The device will automatically rock the eggs every
2 hours. The eggs are rocked to the left and right,
up to 45 degrees for 10 seconds. Do not lift the
cover during automatic egg turning. Pay particular
attention when using the incubator for the first time.
6. Pressing the „reset" button (7) once makes the eggs
rock and resets the timer which counts down to the
next egg rocking (sets it back to 1:59).
EN
7. In order to reset the incubation days counter, press
and hold buttons (3) and (4), then disconnect and
connect the device to the power supply without
releasing the buttons. Device's factory settings will
be restored.
8. Setting the temperature:
• The egg incubator's temperature factory setting is
38°C.
• Press the „Set" (3) button
• Use buttons (4) and (6) to set the heating
temperature.
• Press the „Set" (3) button to confirm the selection.
9. Setting alarm values and calibration:
• To enter settings mode press and hold the „Set" (3)
button for three seconds.
• Use buttons (4) and (6) to switch between the
parameters shown in the table below.
Parameter Parameter meaning Factory setting
AL Setting the low 1°C
temperature alarm.
AH Setting the high 1°C
temperature alarm.
AS Setting the low humidity 45%
alarm.
CA Thermometer calibration. 0°C
HS Setting the upper 39.5°C
temperature limit.
LS Setting the lower 30°C
temperature limit.
• To enter settings of the selected parameter, press
and hold the „Set" (3) button
• Use buttons (4) and (6) to set alarm values. Wait for
the device to automatically return to the main menu.
• The alarm emits a sound signal. To disable the alarm,
press a button on the control panel.
10. Wait for the device to warm up (approx. 10-20 min.).
11. Gently arrange the eggs on the tray.
12. Inspect the water level in the egg incubator regularly.
IN-56DDI, IN-32DDI models
1. Remove cover and lift egg tray. Carefully pour water
into the groove. Close the cover.
2. Connect the device to a power source.
3. Use the On/Off (4) switch to turn the device on.
4. An alarm will sound. Disable the alarm by pressing
a button on the control panel.
5. Setting the temperature:
• The egg incubator's temperature factory setting is
38°C.
• Press the „Set" (2) button
• Use buttons „+" (3) and „-" (5) to set the heating
temperature.
• Press the „Set" (2) button to confirm the selection.
6. Setting alarm values and calibration – in accordance
with operating instructions point 10 for IN-48DDI
and IN-96DDI models
7. Pressing the „reset" button (7) once makes the eggs
rock and resets the timer which counts down to the
next egg rocking (sets it back to 1:59).
27.06.2019
8. In order to reset the incubation days counter, press
and hold the „reset" button (7), then disconnect and
connect the device to the power supply without
releasing the button. Device's factory settings will be
restored.
9. Wait for the device to warm up (approx. 10-20 min.).
10. Gently arrange the eggs on the tray.
11. Inspect the water level in the egg incubator regularly.
12. Use button (6) to activate the egg candler and check
embryo development inside the egg.
IN-88DDI model
1. Remove cover. Fill with water. Close the cover.
2. Connect the device to a power source.
3. Use the On/Off (7) switch to turn the device on.
4. Select the required temperature: press the „SET" (6)
button. The „set" (3) diode will illuminate, indicating
that the device is in settings mode. Use „+" (5) and
„-" (4) buttons to select the temperature. Use the
„SET" (6) button to confirm. The „Work" (2) diode will
come on.
5. Wait for the device to warm up (approx. 10-20 min.).
6. Gently arrange the eggs on the tray.
7. Inspect the water level in the egg incubator regularly
Tips for incubating eggs:
• Before incubating eggs, always check that the
incubator is in operational condition and its
functions are working correctly.
• For best results, it's better to choose medium- or
small-sized eggs for hatching. Fertilized eggs for
incubation should be fresh and cleaned of impurities
on the shell.
• The proper method of placing eggs for hatching is
to arrange them with the wider end upwards and
the narrower end downwards, as shown in the figure
below.
• To avoid hitting the egg with the lid, place large eggs
in the middle of the tray and smaller ones on the
sides. Always check that the egg is not too large to
avoid accidental damage.
• If the eggs are too large to place on the tray, it is
recommended to remove the trays and arrange
the fertilised eggs directly on the white grid (not
applicable for the IN-7DDI model).
• The water level in the incubator should be constantly
monitored to ensure adequate humidity for hatching
eggs.
• If the ambient temperature drops below 20 °C, we
recommend placing the incubator in a unit made of
insulating material, e.g. polystyrene foam, etc. If such
insulation is not possible, it is recommended to place
the incubator in a heated room or surround it with
thick material such as blankets.
• After 19 days of incubation, when the egg shells start
to crack, it is recommended to remove the eggs from
the egg tray and place them on a white grid to hatch
the chicks (does not apply to the IN-7DDI model).
• It often happens that some eggs do not completely
hatch after 19 days, then you should wait another
2-3 days.
27.06.2019
EN
• When a chick gets stuck in the shell, spray the shell
with warm water and help by gently pulling off the
egg shell.
• After hatching, the chicks should be kept in a warm
place and supplied with proper food and water.

3.4. CLEANING AND MAINTENANCE

a) Always unplug the device before cleaning it.
b) Use only non-corrosive cleaners to clean the surface.
c) After cleaning the device, all parts should be dried
completely before using it again.
d) Store the unit in a dry, cool place, free from moisture
and direct exposure to sunlight.
e) Do not spray the device with a water jet or submerge
it in water.
f) Do not allow water to get inside the device through
vents in the housing of the device.
g) Clean the vents with a brush and compressed air.
h) The device must be regularly inspected to check its
technical efficiency and spot any damage.
i) Use a soft cloth for cleaning.
j) Do not leave the battery in the device if it will not be
used for a longer period of time.
k) Disinfect the device after each use.
SAFE REMOVAL OF BATTERIES AND RECHARGEABLE
BATTERIES
An AA 1.5V battery is installed in the egg candler. Use the
On/Off button to turn the candler off before attempting to
remove the battery. Unscrew the back of the housing and
remove the battery. Recycle batteries.
DISPOSING OF USED DEVICES
Do not dispose of this device in municipal waste systems.
Hand it over to an electric and electrical device recycling
and collection point. Check the symbol on the product,
instruction manual and packaging. The plastics used to
construct the device can be recycled in accordance with
their markings. By choosing to recycle you are making
a significant contribution to the protection of our
environment.
Contact local authorities for information on your local
recycling facility.
15