Maintenance And Service; Maintenance And Cleaning; Accessories; After-Sales Service And Application Service - Bosch GCM 80 SJ Professional Notice Originale

OBJ_BUCH-2154-002.book Page 26 Monday, June 16, 2014 2:55 PM
26 | English
Setting the Standard Bevel Angle 45° (Vertical)
– Bring the power tool into the working position.
– Turn the saw table 20 to the 0° detent 26. The lever 24
must be felt to engage in the detent.
– Loosen the lock lever 8 and tilt the tool arm leftward to the
stop (45°) by the handle 14.
Checking: (see figure O1)
– Adjust an angle gauge to 45° and position it on the saw ta-
ble 20.
The leg of the angle gauge must be flush with the saw blade 38
over the complete length.
Adjusting: (see figure O2)
– Loosen the lock lever 8.
– Loosen the lock nut of the stop screw 7 using a commercial
box-end or open-end spanner (size 10 mm).
– Screw the stop screw in or out until the leg of the angle
gauge is flush with the saw blade over the complete length.
– Retighten the lock lever 8 again.
– Afterwards, retighten the lock nut of the stop screw 7
again.
In case the angle indicator 30 is not in a line with the 45° mark
of the scale 29, firstly check the 0° setting for the bevel angle
and the angle indicator again. Then repeat the adjustment of
the 45° bevel angle.
Aligning the Angle Indicator (Horizontally) (see figure P)
– Bring the power tool into the working position.
– Turn the saw table 20 to the 0° detent 26. The lever 24
must be felt to engage in the detent.
Checking:
The angle indicator 22 must be in alignment with the 0° mark
of the scale 3.
Adjusting:
– Loosen screw 46 using a cross-head screwdriver and align
the angle indicator alongside the 0° mark.
– Retighten the screw again.
Transport (see figure Q)
Before transporting the power tool, the following steps must
be carried out:
– Loosen the locking screw 9 if tightened. Pull the tool arm
completely to the front and tighten the locking screw
again.
– Bring the machine into the transport position.
– Remove all accessories that cannot be mounted firmly to
the power tool.
If possible, place unused saw blades in an enclosed con-
tainer for transport.
– For lifting or transporting, hold the power tool by the re-
cessed grips 2 on the side of the saw table 20.
 When transporting the power tool, use only the trans-
port devices and never use the protective devices.
1 609 92A 0HN | (16.6.14)

Maintenance and Service

Maintenance and Cleaning

 Before any work on the machine itself, pull the mains
plug.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
Cleaning
For safe and proper working, always keep the power tool and
its ventilation slots clean.
The retracting blade guard must always be able to move freely
and retract automatically. Therefore, always keep the area
around the retracting blade guard clean.
Remove dust and chips after each working procedure by
blowing out with compressed air or with a brush.
Clean the roller 18 regularly.

Accessories

Material clamp
Insert plates
Dust bag
Saw blades for wood and plate materials, panels and
strips/mouldings
Saw blade 216 x 30 mm, 48 teeth
Saw blades for plastic and non-ferrous metals
Saw blade 216 x 30 mm, 80 teeth
Saw blades for all types of laminate flooring
Saw blade 216 x 30 mm, 60 teeth

After-sales Service and Application Service

In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0844) 7360109
E-Mail: boschservicecentre@bosch.com
Article number
1 609 B04 224
1 609 B05 242
1 609 B00 840
2 608 640 641
2 608 640 447
2 608 642 133
Bosch Power Tools