Maintenance And Service; Maintenance And Cleaning; Accessories - Bosch GCM 216 Professional Notice Originale

– Unscrew the screws (47) using a commercially available
cross-headed screwdriver and remove the old insert
plate (14).
– Insert the new insert plate and screw the screws (47) in
tight again.
Working on mouldings
Mouldings can be sawn in two different ways:
Positioning of Base moulding
workpiece
– Placed against
the fence
– Lying flat on the
saw table
Always check the set mitre and/or bevel angle first by mak-
ing trial cuts in scrap wood.
Checking and Adjusting the Basic Settings
To ensure precise cuts, the basic settings of the power tool
must be checked and adjusted as necessary after intensive
use.
Experience and suitable special tools are required for this.
A Bosch after-sales service point will handle this work
quickly and reliably.
Aligning the fence
– Bring the power tool into the transport position.
– Turn the saw table (12) to the 0° detent . The lever (16)
must be felt to engage in the detent.
– Pull the adjustable fence (23) all the way out.
Checking (see figure P1)
– Set an angle gauge to 90° and position it flush with the
saw blade (41) between the fence (11) and the saw
blade on the saw table (12).
The leg of the angle gauge must be flush with the fence over
the complete length.
Setting (see figure P2)
– Loosen all hex socket screws (48) with the hex key (32)
provided.
– Rotate the fence (11) until the angle gauge is flush over
the complete length.
– Re-tighten the screws.
Aligning the mitre angle indicator (see figure Q)
– Bring the power tool into the work position.
– Turn the saw table (12) to the 0° detent . The lever (16)
must be felt to engage in the detent.
Checking
The angle indicator(17) must be in line with the 0° mark of
the scale (18).
Bosch Power Tools
Setting
– Loosen the screw (49) using a cross-headed screwdriver
and align the angle indicator along the 0° mark.
– Retighten the screw.
Transport (see figure R)
Before transporting the power tool, the following steps must
be carried out:
– Bring the power tool into the transport position.
Crown moulding
– Remove all accessories that cannot be securely fitted to
the power tool.
If possible, transport unused saw blades in a closed con-
tainer.
– Carry the power tool by the transport handle (3) or hold it
by the recessed handles (20) on the sides of the saw
table.
Only use the transport devices to transport the power
u
tool and never the protective devices.

Maintenance and Service

Maintenance and Cleaning

Pull the plug out of the socket before carrying out any
u
work on the power tool.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
after-sales service centre that is authorised to repair Bosch
power tools.
The retracting blade guard must always be able to move
freely and retract automatically. It is therefore important to
keep the area around the retracting blade guard clean at all
times.
Always remove dust and chips after working by blowing out
with compressed air or using a brush.
Clean the guide roller (26) regularly.
Cleaning the laser lens (see figure S)
– Swivel the retracting blade guard (9) to the back and hold
it in this position.
– Loosen the knurled screw (50) for the laser protection
cap (7).
– Pull the clear laser lens cover (51) forwards and out of
the laser protection cap and wipe off any dirt using a dry,
soft cloth.
– Reinsert the cover (51) in the laser protection cap as far
as it will go (7) and retighten the knurled screw (50).

Accessories

Extension bar
Dust bag
Reducing ring 30/25.4 x 1.2 mm
English | 17
Article number
1 619 PB6 147
1 619 PB6 246
2 600 100 211
1 609 92A 72S | (19.11.2021)