General Warnings; General Description; Fuels; Pellet Supply - Bio Bronpi Radiofrequency Série Instructions D'installation, D'utilisation Et D'entretien

1

GENERAL WARNINGS

The installation of the stove must be done according to the local, national or European regulations.
Stoves by Bronpi Calefacción, S.L. are manufactured under a quality control system in order to protect both the user and the fitter in the
event of possible accidents. We also recommend to the authorized installer that, each time an operation in the stove is going to be done,
pay special attention to the electrical connections, especially that stripped or bear wires are never left outside the connections, avoiding
dangerous contacts.
The installation must be performed by authorized personnel who must provide the buyer a declaration of conformity of the
installation where he will assume full responsibility for the final installation and, therefore, the proper operation of the installed
product. Bronpi Calefacción S.L. will not assume any liability in the case of failure to complying with these precautions.
The manufacturer will not assume any liability for damages caused to third parties due to improper installation or misuse of the stove.
In order to ensure the correct operation of the product, components can only be replaced with original spare parts and by an authorized
technician.
Maintenance of the stove must be performed at least once a year by an Authorized Technical Service.
For more security you should consider:
• Do not touch the stove with bare feet or with wet body parts.
• The door of the machine must be closed during operation.
• It is forbidden to modify the safety or regulating devices without the permission of the manufacturer.
• Avoid direct contact with any parts of the product that tend to reach high temperatures during its operation.
2

GENERAL DESCRIPTION

The stove or insert that you have purchased contains the following pieces:
• Complete structure of the stove or insert on the pallet.
• Inside the combustion chamber you can find: a box/bag with a thermal glove that allows us to use the handle of the door and other
components. The electrical interconnection cable between the stove and the network. A hook (cold hands handle) to make easier
the removing and cleaning of the burner. The remote control of the stove or insert (battery included). A yellow leaflet with the most
important warnings and considerations. The doors handle (according to the models). A book in order to register all maintenance tasks
performed to the stove as well as this installation, use and servicing manual.
• Inside the combustion chamber you will also find the burner and the ash pan.
The equipment consists of several elements of steel sheets welded, with different thickness and, depending on the model, pieces of cast iron.
It also has a door with vitro ceramic glass (resistant up to 750ºC) and ceramic cord for the air tightness in the combustion chamber.
Heating is produced by:
a. Forced convection: thanks to the fan placed on the bottom of the stove, the air at room temperature is aspired and it is returned to the
room at a higher temperature.
b. Radiation: through the vitro ceramic glass and the body the heat is irradiated towards the environment.
3

FUELS

WARNING:
The use of a low quality pellet or any other fuel in disagreement with the specifications mentioned below implies the cancellation of
the warranty and the responsibility bounded to the product
Only wood pellets certified by these standards or certifications should be used :
Standards:
• Ö-Norm M 7135 | Din 51731 | EN-14962-2 (all repealed and included in ISO-17225-2)
• ISO-17225-2
Quality certifications:
• DIN+
• ENplus: On the web site (www.pelletenplus.es) you can check all manufacturers and distributors with certificate.
It is strongly recommended that the pellet is certified with quality certifications because this is the only way to guarantee the
constant quality of the pellet.
Bronpi Calefacción recommends the use of pellets with 6 mm diameter, a maximum longer of 3.5 cm and with a humidity percentage lower
than 8%.
•
STORAGE OF PELLET
In order to guarantee combustion without any problem it is necessary to keep the pellet in a dry ambient.
•

PELLET SUPPLY

Open the tank cover on the top of the equipment and empty directly the pellet bag taking care of not overflowing.
In the case of the inserts Damasco and Neva, it is necessary to open the upper tray to do the fuel supply (use the glove provided) and after
that fill up the pellet load tray with a suitable container, taking care not to overflow. Push the drawer inward with the accessory provided
accessory until the pellet falls into the hopper. Repeat this operation several times until you could see the pellet on the hopper through the
drawer (see drawings D1 and D2).
INSTALLATION, OPERATING AND SERVICING INSTRUCTIONS 25 RADIOFREQUENCY SERIES