Wolf Garten Compact plus 40 E-1 Mode D'emploi page 15

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

Connecting to the mains (230 Volts, A.C., 50 Hz)
The mower operates from any normal household mains supp-
ly, provided with a 16 Amps. fuse.
3
Note: Residual current protection device
These protection devices safeguard while touching
damaged wires, from insulation flaws and in certain cases,
also while damaging live wires.
We recommend that the equipment only be plugged into
a power socket, which is protected by a residual current
protection device (RCD) with a residual current of not
more than 30 mA.
Retrofit kits are available for old installations. Consult an
electrician.
Starting and Stoping
Switch on motor with mowerplaced on level and firm ground.
not in high grass - alternatively tilt slightly
Switch-on motor
O
1. Depress button and hold (1).
2. Lift up bar (2).
3. Release bar (2).
Switch-off motor
O
Release bar (2).
Tips for mowing
To prevent strips of grass from being left unmowed, the cutting
paths must always overlap a few centimeters
Always let cable trail on the cut side of the lawn.
Cut / Collect
Activate cut/collect function
1
Attention! Rotary cutter blade
Undertake adjustments on the equipment only after the
motor is switched off and the cutting tool has come to a
standstill.
Do not start the motor until your feet are at a safe
distance from the cutting tool.
1. Remove the grass collecting bag.
2. Turn the switch to "CUT/COLLECT".
3. Hang up the collection bag if necessary.
4. Start the motor.
Hang up collection bag
1
Attention! Rotary cutter blade
Undertake adjustments on the equipment only after the
motor is switched off and the cutting tool has come to a
standstill.
1. Lift the protective flap.
2. Hang the grass bag in the chassis with the hooks in the reces-
ses (see arrow).
3. Replace the protective flap.
G
N
.
P
.
Q
R
Emptying of Grassbox
When the collection bag is full, the flap lowers by itself
1
Attention! Rotary cutter blade
Undertake adjustments on the equipment only after the
motor is switched off and the cutting tool has come to a
standstill.
Switch off motor.
Empty collection bag
Remove potential blockages in the cutting space before
starting.
3
Instructions for level indicator:
For an efficient functioning of the level indicator, regularly
clean the holes under the level indicator in the collection
bag with a hand brush.
Mulch
„Mulching" is a process in which the grass is finely chopped by a
special cutting system and then deposited on the ground. The re-
sult is that the grass does not have to be collected and disposed
of. „Mulching" also prevents the lawn from drying out.
3
Instructions for mulching
We recommend:
Depending on the growth of grass, mulch 1 – 2 x per
week
The grass should not be too high nor too wet!
Go slow while mulching
Take care that the blade channels do overlap.
Do not cut grass more than 20 mm.
3
Note:
Mulching is not advisable in case of moss-affected or
entangled grass, because the cut material stays on the
moss surface and/or entanglement and thus cannot be
absorbed by the ground.
Regularly scarify and manure the lawn.
Activating the mulch function
1
Attention! Rotary cutter blade
Undertake adjustments on the equipment only after the
motor is switched off and the cutting tool has come to a
standstill.
Do not start the motor until your feet are at a safe dis-
tance from the cutting tool.
1. Remove the grass collecting bag.
2. Set the switch to „MULCH".
3. Start the motor.
S
.
T
.
Q
15

Publicité

Table des Matières
loading

Table des Matières