DeWalt D28730 Guide D'utilisation page 10

English
carefully back the brush spring out of the brush box and
remove brush. Brushes should slide freely in brush box.
If brushes are worn down to 5/16" (8 mm) as shown in
Figure J, they should be replaced.
To reinstall each brush, carefully back the spring out of the
brush box, insert the brush and return the spring making
sure it is pressing on the brush and not touching the brush
box. Reconnect shunt wire terminal, then replace the end
cap and two screws.
Fig. I
22
FIg. J
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
Accessories

WARNING: Since accessories, other than those
offered by D WALT, have not been tested with this
e
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
8
24
23 25
24
5/16"
(8 mm)
WALT
e
Recommended accessories for use with your tool
are available at extra cost from your local dealer or
authorized service center. If you need assistance in
locating any accessory, please contact D
Tool Co., 701 East Joppa Road, Towson, MD 21286, call
1-800-4-D WALT (1-800-433-9258) or visit our website:
e
www.dewalt.com.
Repairs

WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
should be performed by a D
center or a D WALT authorized service center. Always
e
use identical replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRAnTY sERViCE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with your product.
• COnFiRMATiOn OF OWnERshiP: In case of
an insurance loss, such as fire, flood or theft, your
registration of ownership will serve as your proof
of purchase.
FOR YOUR sAFETY: Registering your product will
•
allow us to contact you in the unlikely event a safety
notification is required under the Federal Consumer
Safety Act.
Register online at www.dewalt.com/register.
Three Year Limited Warranty
D WALT will repair, without charge, any defects due to
e
faulty materials or workmanship for three years from
the date of purchase. This warranty does not cover part
failure due to normal wear or tool abuse. For further detail
of warranty coverage and warranty repair information,
visit www.dewalt.com or call 1-800-4-D
433-9258). This warranty does not apply to accessories
or damage caused where repairs have been made
or attempted by others. THIS LIMITED WARRANTY IS
GIVEN IN LIEU OF ALL OTHERS, INCLUDING THE IMPLIED
WARRANTY OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, AND EXCLUDES ALL INCIDENTAL
OR CONSEQUENTIAL DAMAGES. Some states do not allow
limitations on how long an implied warranty lasts or the
exclusion or limitation of incidental or consequential
damages, so these limitations may not apply to you. This
warranty gives you specific legal rights and you may have
other rights which vary in certain states or provinces.
In addition to the warranty, D
by our:
1 YEAR FREE sERViCE
D WALT will maintain the tool and replace worn parts
e
caused by normal use, for free, any time during the first year
after purchase.
90 DAY MOnEY BACK gUARAnTEE
If you are not completely satisfied with the performance of
your D WALT Power Tool, Laser, or Nailer for any reason, you
e
WALT Industrial
e
WALT factory service
e
WALT (1-800-
e
WALT tools are covered
e