Handlebar Adjustment; Cable Adjustment - Eurosystems MFL 04 Manuel D'utilisation

INFORMATION!
If the engine is "cold", operate the start-
er on the carburettor (depending on the
motor version). See the specific manual.
3 .2 3 .2 3 . 3 3 . 3
To start:
Once the engine has started, move the le-
ver in figure 3 . 2 3 . 2 to the intermediate
position.
3 .4 3 .4
To switch off:
7.3 MACHINE COMMANDS
The forward and tool engagement com-
mands are maintained and activated by
double control.
FORWARD MOVEMENT:
3 .6 3 .6
TOOL ENGAGEMENT:

7.4 HANDLEBAR ADJUSTMENT

3 . 7 3 . 7
8. HANDLING AND TRANSPORT
DANGER!
Before proceeding, read and understand
the chapter "SAFETY INSTRUCTIONS"
in its entirety.
With the motor off, the machine can be
moved by hand by pushing or pulling it
from the handlebar.
3 .8 3 .8
LIFTING:
DANGER!
Fit all the guards depending on the type
of the tool.
9. STORAGE
When the machine is not going to be used
for long periods of time, it is essential to
Checking the tightness of
fasteners and guards
Cleaning
Inflation

Cable adjustment

Base oil change
Motor
protect the tool with anti-corrosion and
antioxidant substances.
Clean the machine of leaves and/or dirt
before storage.
DANGER!
Remove the fuel from the tank and close
the tap (if present).
Park the machine on flat ground, removing
the ignition key (if present) and/or spark
plug cap.
DANGER!
Protect the sharp parts and cover the
machine with protective sheets if neces-
sary.
3 .5 3 .5
DANGER!
Fit all the guards depending on the type
of the tool.
10. PERIODIC MAINTENANCE
Keep all nuts, bolts and screws tightened
to ensure safe operation of the machine
and/or interchangeable equipment in safe
conditions.
DANGER!
Before proceeding, read and understand
the chapter "SAFETY INSTRUCTIONS"
in its entirety.
10.1 CABLE ADJUSTMENT
Forward lever:
Machine movement must begin when the
forward lever exceeds half of the stroke as
shown in the figure.
4 . 1 4 . 1
If not, the cable pull must be adjusted
using the register shown in the figure.
4 . 2 4 . 2
Tool engagement lever:
Machine movement must begin when the
12. MAINTENANCE PLAN
Always before starting the machine - check that there are no untightened
screws, bolts and/or nuts and that the bonnets and protection systems are
intact and correctly fitted.
After each use
As needed
If operation is not as according to the manual
60 hours
See specific manual
tool lever exceeds half of the stroke as
shown in the figure
If not, the cable pull must be adjusted
using the register shown in the figure.
The oil in the base of the machine must
be changed every 60 hours or so of work.
Lift the machine as described in the "HAN-
DLING AND TRANSPORT" chapter.
Then proceed as follows:
Use a syringe (not included) for easier
and safer extraction.
Use SAE 80 or equivalent oil.
Proceed in reverse order to reassemble
the wheel.
Before proceeding, read and under-
stand the chapter "SAFETY INSTRUC-
TIONS" in its entirety.
Wait for all the hot parts to cool down (at
least 20 minutes) before washing and/or
cleaning the machine or the interchange-
able equipment. Use compressed air or a
sponge with neutral detergent and water.
Do not use pressurised water to wash the
machine and/or interchangeable equip-
ment. Doing so can damage the motor
and any electrical systems or batteries.
How often
4 . 3 4 . 3
.
4 . 4 4 . 4
10.2 MACHINE OIL CHANGES
4 . 5 4 . 5 4 . 6 4 . 6 4 .7 4 .7
INFORMATION!
CAUTION!
11. CLEANING AND WASHING
DANGER!
CAUTION!
See chapt.
-
11.
10.3
10.1
10.2
4 .8 4 .8