Publicité
Les langues disponibles
Les langues disponibles
ACTIVATION PROCEDURE
Before using the radio control, follow the procedure below on the hood pushbutton panel:
• Press LIGHT (
) and TIMER (
) simultaneously until all LEDs start lashing.
• Release the two keys and press LIGHT (
• Release LIGHT (
): now the receiver is active.
This procedure is also used to deactivate the receiver.
RADIO CONTROL CODE CHANgE
With only one radio control, go directly to point 2.
With several radio controls in the same room, a new code can be created by following the
procedure below.
Disconnect the power to the hood before starting the procedure.
1) - cREATE A NEW cODE
The procedure is to be carried out on the radio control.
• Press LIGHT
and TIMER
simultaneously until the display starts lashing.
• Press DOWN
on the radio control: saving is conirmed by three brief lashes of the
display. The new code cancels and replaces the previous default code.
Reconnect the hood to the electrical power supply, making sure that the
lights and motor are of.
2A) - ASSOcIATINg THE RADIO cONTROL WITH THE HOOD
USINg THE ELEcTRONIc PUSHBUTTON PANEL
press TIMER (
) on the hood pushbutton panel for 2 seconds:
the red LED lights up.
press any key on the radio control within 10 seconds.
RESTORINg DEFAULT cODE
the procedure is to be carried out if the hood is disposed of, sold or transferred.
Disconnect the power to the hood before starting the procedure.
• Press UP
and DOWN
simultaneously on the radio control for more than 5 sec-
onds: reset is conirmed by three brief lashes of the display.
• Reconnect the hood to the electrical power supply.
• Proceed with associating the hood and the radio control, as described in point 2.
mAINTENANcE
Before cleaning or carrying out maintenance operations, disconnect the
equipment by removing the plug or switching of the main switch.
Do not use detergents containing abrasive, acidic or corrosive substances
or abrasive cloths.
Regular maintenance guarantees proper operation and performance over time.
Special attention is to be paid to the metal anti-grease ilters : frequent cleaning of the
ilters and their supports ensures that no lammable grease is accumulated.
cLEANINg OF ExTERNAL SURFAcES
You are advised to clean the external surfaces of the hood at least once every 15 days to
prevent oily substances and grease from sticking to them. To clean the brushed stainless
steel hood, the Manufacturer recommends using "Magic Steel" wipes.
Alternatively and for all the other types of surfaces, it can be cleaned using a damp cloth,
slightly moistened with mild, liquid detergent or denatured alcohol.
Complete cleaning by rinsing well and drying with soft cloths.
Do not use too much moisture or water around the push button control
panel and lighting devices in order to prevent humidity from reaching
electronic parts.
The glass panels can only be cleaned with speciic, non-corrosive or non-abrasive deter-
gents using a soft cloth.
The Manufacturer declines all responsibility for failure to comply with these instructions.
) again until all LEDs are lit up.
cLEANINg OF INTERNAL SURFAcES
Do not clean electrical parts, or parts related to the motor inside the hood,
with liquids or solvents.
For the internal metal parts, see the previous paragraph.
mETAL ANTI-gREASE FILTERS
It is advised to frequently wash the metal ilters (at least once a month) leaving them to
soak in boiling water and cleaning solution for 1 hour, taking care not to bend them.
Do not use corrosive, acid or alkaline detergents.
Rinse them well and wait for them to be completely dry before reassembling them.
Washing in a dishwasher is permitted, however, it may cause the ilter material to darken: to
reduce the possibility of this problem from happening, use low-temperature washes (55°C
max.).
To extract and insert the metal anti-grease ilters see the assembly instructions.
HP/AcTIvE cARBON FILTERS (optional)
These ilters retain the odours in the air that passes through them. The puriied air is recircu-
lated into the environment.
The HP active carbon ilters reactivate by washing them in the dishwasher with a normal
detergent at a maximum temperature of 65°C and passing them in the oven at 100°C for
10 minutes.
The maximum duration of the ilter is 2/3 years with a maximum of 10 washings per year.
LIgHTINg
The range hood is equipped with high eiciency, low consumption LED lighting with extre-
mely long duration under normal use conditions.
In case of failure, contact the Dealer or an authorised Servicing Department for repairs.
DISPOSAL AFTER END OF USEFUL LIFE
The crossed-out trash or refuse bin symbol on the appliance means that the
product is WEEE, i.e. "Waste electrical and electronic equipment'' , accordingly it
must not be disposed of with regular unsorted waste (i.e. with ''mixed house-
hold waste''), but it must be disposed of separately so that it can undergo specif-
ic processing for its re-use, or a speciic treatment, to remove and safely dispose of any
substances that may be harmful to the environment and remove the raw materials that can
be recycled. Proper disposal of these products contributes to saving valuable resources and
avoid potential negative efects on personal health and the environment, which may be
caused by inappropriate disposal of waste.
You are kindly asked to contact your local authorities for further information regarding the
designated waste collection points nearest to you. Penalties for improper disposal of such
waste can be applied in compliance with national regulations.
INFORmATION ON DISPOSAL IN EUROPEAN UNION cOUNTRIES
The EU WEEE Directive was implemented diferently in each country, accordingly, if you wish
to dispose of this appliance we suggest contacting your local authorities or dealer to ind
out what the correct method of disposal is.
INFORmATION ON DISPOSAL IN NON-EUROPEAN UNION cOUNTRIES
The crossed-out trash or refuse bin symbol is only valid in the European Union: if you wish
to dispose of this appliance in other countries, we suggest contacting your local authorities
or dealer to ind out what the correct method of disposal is.
WARNINg!
The Manufacturer reserves the right to make changes to the equipment at any time and
without prior notice. Printing, translation and reproduction, even partial, of this manual are
bound by the Manufacturer's authorisation.
Technical information, graphic representations and speciications in this manual are for in-
formation purposes and cannot be divulged.
This manual is written in Italian. The Manufacturer is not responsible for any transcription
or translation errors.
20
Publicité
