Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
List of Materials
Removing the packaging
CAUTION!
Remove carton carefully, wear gloves to protect against sharp edges.
WARNING!
Remove the protective film covering the product before putting into
operation.
Parts supplied
•
Downdraft assembly with blower already installed
•
Metal grease filters
•
2 - Lower support legs
•
2 - End caps
•
6" round air transition
•
3
⁄
"x10" rectangular air transition
1
4
•
Metalic top trim
•
Control assembly
•
Hardware bag with:
• Use, care and installation guide
• Plastic control base
• 1 - Shrinkable wire tube
• 2 - Plastic wire ties
• 2 - Installation brackets
• 4 - Plastic clips for aspiration plate
• 7 - Adhesive wire clips
• 8 - 4 x 8 mm mounting screws
• 11 - 4.5 x 13 mm mounting screws
• 3 - 3.5 x 9.5 mm transition mounting screws
13
⁄
" (34.3 cm)
1
2
retractable
vent height
27" (68.6 cm) for 30" model
33" (83.8 cm) for 36" model
13
⁄
"
1
8
(33.4 cm)
16
⁄
"
1
2
(42 cm)
Product Dimensions
Top trim widths:
30" (76.2 cm)
36" (91.4 cm)
⁄
"
19
32
(1.5 cm)
1
⁄
"
1
2
(3.8 cm)
28
⁄
"
1
2
(72.6 cm)
5
⁄
" (13.3 cm)
1
4
for 30" models
8
⁄
" (21 cm)
1
4
for 36" models
10"
(25.4 cm)
2
⁄
"
1
8
(5.4 cm)
Parts needed
•
Home power supply cable
•
½" (12.7 mm) UL listed or CSA approved strain relief
•
3 UL listed wire connectors
•
1 wall or roof cap
•
6" round metal vent system or 3
Tools/Materials required
•
Level
•
Drill with 1¼" (3.2 cm),⅛" (3.2 mm), and
drill bits
•
Pencil
•
Wire stripper or utility knife
•
Tape measure or ruler
•
Pliers
•
Caulking gun and weatherproof caulking compound
•
Vent clamps
•
Jigsaw or keyhole saw
•
Flat-blade screwdriver
•
Metal snips
Cabinet Dimensions
⁄
" (1.27 cm)
1
2
minimum
21
⁄
"
5
16
(54.1 cm)
Cutouts are
for 3
⁄
" x 10"
1
4
(8.3 x 25.4 cm)
rectangular or 6"
(15.2 cm) round
vent system.
Locate power supply
junction box at lower
left hand rear corner
of the cabinet.
NOTES:
•
See cooktop manufacturer's instructions for cooktop cutout
depth and width.
•
Use dimensions for vent system cutout location that applies to
your installation.
•
Interior mounted blower systems connect with 3
(8.3 x 25.4 cm) rectangular or 6" (15.2 cm) round vent system.
The cutout locations for this vent system will depend on your
specific installation.
5
⁄
"x10" rectangular vent system
1
4
⁄
" (7.9 mm)
5
16
9
⁄
"
1
2
(24.4 cm)
21
⁄
"
5
16
(54.1 cm)
Centerline of
cooktop cutout
⁄
" x 10"
1
4
Publicité
Chapitres
Table des Matières
