Publicité
Les langues disponibles
Les langues disponibles
■
To reduce the risk of injury associated with contacting
moving parts, always turn off the product, remove the
battery pack, and allow both to cool down. Make sure
that all moving parts have come to a complete stop:
●
before servicing
●
before clearing a blockage
●
before checking, cleaning, and working on the
product
●
before changing accessories
●
after striking a foreign object
●
whenever leaving the product unattended
●
whenever performing maintenance
●
whenever the product starts to vibrate abnormally
■
Wear full eye and hearing protection while operating the
product. If working in an area where there is a risk of
falling objects, head protection must be worn.
■
Hearing protection may restrict the operator's ability
to hear warning sounds. Pay particular attention to
potential hazards around and inside the working area.
■
Wear heavy, long trousers, boots, and gloves. Do not
wear loose-fitting clothing, short trousers, or jewellery of
any kind. Do not use the product with bare feet.
■
Secure long hair so that it is above shoulder level to
prevent entanglement in moving parts.
■
The small blade fitted to the lawn guard is designed to
trim the newly extended line to the correct length for safe
and optimum performance. The blade is very sharp.
Do not touch the blade, particularly when cleaning the
product.
■
Always ensure that ventilation openings are kept clear
of debris.
■
Before use and after any impact, check that there are no
damaged parts on the product. A defective switch or any
part that is damaged or worn should be properly repaired
or replaced by an authorised service centre.
■
Make sure that the cutting head attachment is properly
installed and securely fastened.
■
Make sure that all guards, deflectors, and handles are
properly and securely attached.
■
Do not modify the product in any way. This may increase
the risk of injury to yourself or others.
■
Use only the manufacturer's replacement cutting line.
Do not use any other cutting attachment.
■
Immediately turn off the product and remove the battery
pack in the event of an accident or breakdown. Do not
operate the product again until it has been fully checked
by an authorised service centre.
■
Ensure that the line cut-off blade in the guard is properly
positioned and secured before each use.
ADDITIONAL BATTERY SAFETY WARNINGS
To reduce the risk of fi re, personal injury, and product
damage due to a short circuit, never immerse the tool,
battery pack, or charger in fl uid or allow fl uid to fl ow inside
them. Corrosive or conductive fl uids, such as seawater,
certain industrial chemicals, and bleach or bleach-containing
products, etc., can cause a short circuit.
4
Original Instructions
TRANSPORTATION AND STORAGE
■
Turn off the product, remove the battery pack, and allow
both to cool down before storing or transporting.
■
Remove all foreign materials from the product.
■
Do not store or transport the product with the battery
pack fitted. Remove the battery pack and secure it
separately. Store the product in a cool, dry, and well-
ventilated place that is inaccessible to children. Keep
the product away from corrosive agents, such as garden
chemicals and de-icing salts. Do not store the product
outdoors.
■
For transportation in vehicles, secure the product
against movement or falling to prevent injury to persons
or damage to the product.
TRANSPORTING LITHIUM BATTERIES
■
Transport the battery pack in accordance with local and
national provisions and regulations.
■
Follow all special requirements on packaging and
labelling when transporting batteries by a third party.
Ensure that no batteries can come in contact with other
batteries or conductive materials while in transport
by protecting exposed connectors with insulating,
nonconductive caps or tape. Do not transport batteries
that are cracked or leaking. Check with the forwarding
company for further advice.
MAINTENANCE
■
Use only original manufacturer's replacement parts,
accessories, and attachments. Failure to do so can cause
possible injury, can contribute to poor performance, and
may void your warranty.
■
Servicing requires extreme care and knowledge
and should be performed only by a qualified service
technician. Have the product serviced by an authorised
service centre only.
■
Turn off the product and remove the battery back before
conducting any maintenance or cleaning work.
■
You may make adjustments or repairs described in this
manual. For other repairs, contact an authorised service
centre.
■
For the replacement line, use only a nylon filament line
of the diameter described in the specifications table of
this manual.
■
After each use, clean the product with a soft, dry cloth.
Any part that is damaged should be properly repaired or
replaced by an authorised service centre.
■
Check all nuts, bolts, and screws before each use and
at frequent intervals for proper tightness to ensure that
the product is in safe working condition. Any part that is
damaged should be properly repaired or replaced by an
authorised service centre.
■
Bring the product to an authorised service centre to
replace damaged or unreadable labels.
■
Injuries may be caused, or aggravated, by prolonged
use of a tool. When using any tool for prolonged periods,
ensure that you take regular breaks.
Publicité
