Standard Accessories; Applications; Prior To Operation - HIKOKI D 13 Mode D'emploi

SPECIFICATIONS
Voltage (by areas)*
1
Power input
No load speed
Steel
Capacity
Wood
Weight (without cord)*
2
*1 Be sure to check the nameplate on product as it is subject to change by areas.
*2 According to EPTA-Procedure 01/2014.

STANDARD ACCESSORIES

(1) Chuck wrench ..............................................................1
(2) Side handle ..................................................................1
Standard accessories are subject to change without notice.
OPTIONAL ACCESSORIES (sold separately)
(1) Handle joint
(2) Depth Stopper
Optional accessories are subject to change without notice.

APPLICATIONS

○ Drilling in metal, lumber and plastics.

PRIOR TO OPERATION

1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specifi ed on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position. If the
plug is connected to a receptacle while the power switch
is in the ON position, the power tool will start operating
immediately, inviting serious accident.
3. Extension cord
When the work area is removed from the power source.
Use an extension cord of suffi cient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
4. Confi rm the direction of bit rotation
The drill bit rotates clockwise (when viewed from the
rear) when the lever of the reversing switch is set to the
"R" position, and rotates in the reverse direction when the
lever of the reversing switch is set to the "L" position.
5. Fitting the drill bit
Fit the drill bit into the chuck and use the chuck key to
secure it, tightening the chuck by each of the three holes
in turn.
6. Selecting the appropriate drill bit
○ When boring metal or plastic
Use ordinary metalworking drill bits.
Sizes range from a minimum of 1.2 mm to chuck
maximum capacity.
○ When boring wood
Use ordinary woodworking drill bits.
However, when drilling 6.5 mm or smaller holes, use a
metalworking drill bit.
(110 V, 115 V, 120 V, 127 V, 220 V, 230 V, 240 V)
720 W*
650 min
13 mm
40 mm
3.1 kg
7. Installing spade handle
The spade handle can be installed on the back of the
drill. Insert the bolt through the hole in the spade handle,
locate the spade handle in the desired position and
tighten the bolt fi rmly.
8. Installing the side handle
The side handle screws into the housing on either side of
the gear cover. For safe operation, use of the side handle
is necessary. Especially in heavy duty drilling, use handle
joint and side handle.
9. Installing the depth stopper (optional accessory)
The depth stopper which is useful for adjusting the drilling
depth is available. Install the depth stopper to the gear
cover using the side handle or set screw.
10. RCD
The use of a residual current device with a rated residual
current of 30 mA or less at all times is recommended.
PRACTICAL HANDLING PROCEDURES
1. Pressure
Drilling will NOT be accelerated by placing heavy
pressure on the drill. Such action will only result in a
damaged drill bit, decreased drilling effi ciency, and/or
shortened service life of the drill.
2. Using a large diameter drill bit
The larger the drill bit diameter, the larger the reactive
force on your arm. Be careful not to lose control of the drill
because of this reactive force. To maintain fi rm control,
establish a good foothold, hold the drill tightly with both
hands, and ensure that the drill is vertical to the material
being drilled.
3. When drilling completely through the material
When the drill bit bores completely through the
material, careless handing often results in broken drill
bit or damage to the drill body itself due to the sudden
movement of the drill.
Always be alert and ready to release pushing force when
drilling through the material.
4. Switch operation
(1) Trigger switch
By pulling the trigger switch and depressing the stopper,
the switch is held in the ON position for continuous
drilling. To turn the drill OFF, pull the trigger switch again
and release.
(2) Reversing switch
This drill can rotate both clockwise (for drilling) and
counterclockwise (for releasing the drill bit) by operating
the reversing switch.
English
1
*
–1 1
7