Impact Drill Safety Warnings; Standard Accessories; Applications; Prior To Operation - HIKOKI FDV 16VB2 Mode D'emploi

English

IMPACT DRILL SAFETY WARNINGS

1. Wear ear protectors with impact drills.
Exposure to noise can cause hearing loss.
2. Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
SPECIFICATIONS
Voltage (by areas)*
Power input
No load speed
Capacity
Weight (without cord)
* Be sure to check the nameplate on product as it is subject to change by areas.

STANDARD ACCESSORIES

For entire area
(1) Side handle ..................................................................1
(2) Depth stopper ...............................................................1
For partial areas
(1) Chuck wrench ..............................................................1
(For drill chuck with chuck wrench)
(2) Plastic case ..................................................................1
Standard accessories are subject to change without notice.

APPLICATIONS

○ By combined actions of ROTATION and IMPACT:
Boring holes in concrete, marble, granite, tile, and
similar materials.
○ By ROTATIONAL action:
Boring holes in metal, wood and plastic.
Tightening wood screws.

PRIOR TO OPERATION

1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specifi ed on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position. If
the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, inviting serious accident.
3. Extension cord
When the work area is removed from the power source.
Use an extension cord of suffi cient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
4. Fixing the side handle
Attach the side handle to the mounting part.
Rotate the side handle grip in a clockwise direction to
secure it.
Set the side handle to a position that is suited to the
operation and then securely tighten the side handle
grip.
6
Steel
Concrete
Wood
3. Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live" and
could give the operator an electric shock.
(110V, 115V, 120V, 127V, 220V, 230V, 240V)
550 W*
0–2900 min
13 mm
16 mm
25 mm
1.6 kg
5. Mounting and dismounting of the bit
For keyless chuck
(1) Mounting the bit
After inserting a driver bit, etc. into the keyless drill
chuck, fi rmly grasp the ring and tighten the sleeve by
turning it toward the right (in the clockwise direction as
viewed from the front) (See Fig. 1).
○ If the sleeve becomes loose during operation, tighten
it further. The tightening force becomes stronger when
the sleeve is tightened.
(2) Dismounting the bit
Firmly grasp the ring and loosen the sleeve by turning
it toward the left (in the counterclockwise direction as
viewed from the front) (See Fig. 1).
NOTE
When the sleeve does not become loose any further, fi x
the side handle to the sleeve. Then, strike the grip of the
side handle to the left in order to loosen the sleeve,while
holding the ring by hand (Fig. 2).
CAUTION
Do not fi x the side handle to the ring of the keyless
chuck because of a risk that doing so may damage the
ring.
For Drill chuck with chuck wrench
Fit the drill bit into the chuck and use the chuck wrench
to secure it, tightening the chuck by each of the three
holes in turn (Fig. 3).
6. Selecting the appropriate drill bit
○ When boring concrete or stone:
Use the drill bits for concrete.
○ When boring metal or plastic:
Use an ordinary metalworking drill bit.
○ When boring wood:
Use an ordinary woodworking drill bit.
However, when drilling 6.5 mm or smaller holes, use a
metalworking drill bit.
7. Selecting the driver bit
Screw heads or bits will be damaged unless a bit
appropriate for the screw diameter is employed to drive
in the screws.
8. Check the rotational direction (Fig. 4)
The bit rotates clockwise (viewed from the rear side) by
pushing the R-side of the push button.
The L-side of the push button is pushed to turn the bit
counterclockwise.
(The and marks are provided on the body.)
L R
–1