Publicité
Les langues disponibles
Les langues disponibles
TROUBLESHOOTING
Proper cleaning, maintenance and the use of clean, dry, quality fuel will prevent common operational problems. When your Louisiana Grills® grill
is operating poorly, or on a less frequent basis, the following troubleshooting tips may be helpful. For FAQ, please visit www.louisiana-grills.com .
You may also contact your local Louisiana Grills® authorized dealer or contact Customer Care for assistance.
WARNING: ALWAYS DISCONNECT THE ELECTRICAL CORD PRIOR TO OPENING THE GRILL FOR ANY INSPECTION, CLEANING,
MAINTENANCE OR SERVICE WORK. ENSURE THE GRILL IS COMPLETELY COOLED TO AVOID INJURY.
PROBLEM
POSSIBLE CAUSES
Power light not flashing on
Master Switch is off
Control Board
Not connected to power
source
Fuse blown
The GFCI outlet has been
tripped
Faulty Control Board
Fire in burn grate will not
Burn grate
light
Auger motor is jammed
Readout of actual
Grill probe dirty
temperature will not adjust
Grill probe is broken
Frequent flare-ups
Cooking temperature
Grease build-up
Flame broiler is open
Grill produces excess or
Grease build-up
discolored smoke
Wood pellet quality
Burn grate is blocked
Insufficient air intake for fan
Grill will not achieve
Insufficient air flow through
or maintain stable
burn grate
temperature
Lack of fuel, poor fuel
quality, obstruction in feed
system
Grill probe
SOLUTION
Flip the Master Switch on the underside of the Control Board.
Ensure unit is plugged into a working power source. Reset breaker. Ensure GFCI
is a minimum 10 amp service (see electric wire diagram for access to electric
components). Ensure all wire connections are firmly connected and dry.
Disconnect the unit from the power source and remove hopper access panel (see
electric wire diagram for diagram). Pull the Control Board out and then check
the fuse for a broken wire or if the wire has turned black. If yes, fuse needs to be
manually replaced.
Remove hopper access panel (see electric wire diagram for diagram), and ensure
all wire connections are firmly connected and dry. Ensure GFCI is a minimum 10
amp service.
Control Board needs to be replaced. Contact Customer Care for replacement part.
Check burn grate for proper positioning. Follow care and maintenance for ash
build-up.
Turn the unit off by pressing and holding the power button for three seconds.
Remove the cooking components from the Main Barrel. Press the power button to
turn the unit on, and inspect the auger feed system. Visually confirm that the auger
is dropping pellets into the burn grate. If not operating properly, call Customer
Care for assistance.
Follow care and maintenance instructions.
Grill probe needs to be replaced. Contact Customer Care.
Attempt cooking at a lower temperature. Grease does have a flash point. Keep the
temperature under 180°C / 350°F when cooking highly greasy food.
Follow care and maintenance instructions.
Close the flame broiler for indirect flame cooking.
Follow care and maintenance instructions.
Remove moist wood pellets from hopper. Follow care and maintenance
instructions to clean out. Replace with dry wood pellets.
Clear burn grate of moist, wood pellets. Follow hopper priming procedure.
Check fan. Ensure it is working properly and air intake is not blocked. Follow care
and maintenance instructions if dirty.
Check proper positioning of cooking components. Check burn grate for proper
positioning. Follow care and maintenance instructions for ash build-up. Check
that the air intake for the fan is not blocked. If no blockage, remove hopper access
panel (see electric wire diagram for diagram) and locate the blue and white fan
wires. Ensure that connection is tight by lightly tugging on each wire. If loose, push
back into connector until it clicks. Check fan blades for cleanliness.
Check hopper to check that fuel level is sufficient, and replenish if low. Should
the quality of wood pellets be poor, or the length of the pellets too long, this may
cause an obstruction in the feed system. Remove pellets and follow care and
maintenance instructions.
Check status of grill probe. Follow care and maintenance instructions if dirty.
Contact Customer Care for a replacement part if damaged.
www.louisiana-grills.com
15
Publicité
