Husqvarna LB 548i Manuel D'utilisation page 24

To use the drive on the wheels (LC
551iV)
• Pull the drive bail in the direction of the handlebar to
start the drive. (Fig. 60)
• Push + and - on the control panel to set the drive
speed in 4 steps. (Fig. 61)
• Release the drive bail to disengage the drive, for
example when you go near an obstacle.
To use the drive on the wheels
(LB 553iV)
1. Start the product, refer to
page 23 .
2. Pull the drive control lever up to start the drive. (Fig.
62)
3. Push + and –buttons on the control panel to set the
drive speed. (Fig. 61)
4. Push the drive control lever down to disengage the
drive, for example when you go near an obstacle.
(Fig. 63)
To move the product with the cutting
equipment disengaged (LB 553iV)
• Engage the start inhibitor.
• Pull up the drive control lever.
• Hold the drive control lever and move the product.
• Let go of the drive control lever and disengage the
start inhibitor to continue the operation.
To use the SavE function
The product has a battery saving function (SavE) that
gives longer operation time.
1. Push the SavE button (A) to start the function. The
SavE symbol (B) on the display comes on.
2. Push the SavE button again to stop the function. The
SavE symbol (B) on the display goes out. (Fig. 64)
Note:
The SavE function stops automatically if the
ground conditions make it necessary to have a higher
output. The SavE function starts automatically again
when the ground conditions let it.
PowerBoost function
When the product cuts long or wet grass, the motor
automatically increases rpm. To save battery time, the
motor goes back to standard mode automatically when
the PowerBoost function is not necessary.
Motor stalling
During operation, the blade and motor can temporarily
stop because of obstacles such as grass blockage
below the cutting cover. If this occurs and you keep the
motor brake handle pushed down, the product restarts
24
To start the product on
automatically. If the product does not restart in 5-10
seconds, it can be necessary to clean below the cutting
To clean the product on page 26 .
cover. Refer to
WARNING:
product tries to restart automatically for 5-10
seconds. Wait for a minimum of 15 seconds
before you do a check of the cutting cover.
WARNING:
cutting cover, release the motor brake
handle, remove the safety key, remove
the batteries and wait for a minimum of
5 seconds. There is a risk of injury if
the obstacle is removed and the product
accidentally starts.
To stop the product
The product stops automatically if you do not operate it
for 3 minutes.
1. Release the motor brake handle to stop the motor.
(Fig. 23)
2. Push the ON/OFF button on the control panel. All
LED lights and symbols on the display go out. (Fig.
65)
3. Remove the safety key from the safety lock and put
it in the safety key holder.
To get a good result
• Always use a sharp blade. A blunt blade gives an
irregular result and the cut surface of the grass
becomes yellow. A sharp blade also uses less
energy than a blunt blade.
• Do not cut more than ⅓ of the length of the grass.
Cut first with the cutting height set high. Examine the
result and lower the cutting height to an applicable
level. If the grass is very long, drive slowly and cut 2
times if necessary.
• Cut in different directions each time to prevent
stripes in the lawn.
• Keep the cutting cover clean. Buildup from grass
and dirt on the inner side of the cutting cover can
decrease the cutting result. Refer to
product on page 26 .
To cut grass without a grass catcher or
mulch plug attached (LC 551iV)
1. Lift up the rear cover and remove the grass catcher.
2. If a mulch plug and a mulch blade are attached,
remove them.
3. Close the rear cover before you operate the product.
When you operate the product, the cut grass discharges
below the rear cover.
If the motor stops, the
Before a check of the
To clean the
1630 - 005 - 07.07.2023