Husqvarna LB 548i Manuel D'utilisation page 23

is shown for 5 seconds after the product is switched off
or the battery indicator button is pressed. The warning
symbol on the battery is on when an error has occurred.
Battery on page 26 .
See
(Fig. 52)
LED lights
All LEDs are lit
LED 1, LED 2, LED 3 are
lit
LED 1, LED 2 are lit
LED 1 is lit
LED 1 flashes
To charge the battery
Charge the battery before the first use. The battery is
only 30% charged when supplied to the customer.
Note:
The battery charger must be connected to the
voltage and frequency specified on the rating plate.
The battery does not charge if the battery temperature
is above 50°C. The battery charger decreases the
temperature of the battery before it starts to charge.
1. Connect one end of the power cord for the battery
charger into the socket of the battery charger.
2. Connect the other end of the power cord for the
battery charger in an grounded mains socket. The
LED on the battery charger flashes green one time.
(Fig. 53)
3. Put the battery in the battery charger. The green
light on the charger comes on when the battery is
correctly connected to the battery charger. (Fig. 54)
4. When all LEDs on the battery have come on the
battery is fully charged. Charge the battery for
maximum 24 hours.
5. To disconnect the battery charger from the mains
socket, pull the plug, not the power cord.
6. Remove the battery from the battery charger.
Battery charging status
A Husqvarna Li-ion battery can be charged or used at
all charging levels. The battery is not damaged. A fully
charged battery will not decrease its charge when the
battery is left in the charger.
LED display
LED 1 flashes
LED 1 is lit, LED 2 flashes 25%-50%
1630 - 005 - 07.07.2023
Battery status
Fully charged (75-100%)
The battery is 50%-75%
charged
The battery is 25%-50%
charged
The battery is 0%-25%
charged.
The battery is empty.
Charge the battery.
Charging status
0%-25%
LED display
LED 1, LED 2 are lit, LED
3 flashes
LED 1, LED 2, LED 3 are
lit, LED 4 flashes
LED 1, LED 2, LED 3,
LED 4 are lit
To charge the multi battery
Note:
Charge the battery if it is the first time that you
use it. A new battery is only 30% charged.
1. Make sure that the battery is dry.
2. Connect the multi battery to the adapter. (Fig. 55)
3. Put the adapter in the battery charger.
4. Make sure that the green charging LED on the
battery charger comes on. That means that the
adapter and multi battery are connected correctly.
(Fig. 56)
5. When all LEDs on the battery come on and the
adapter shows 100%, the battery is fully charged.
(Fig. 57)
The adapter shows the state of charge in steps of
1%. Small deviations are possible at the start of the
charge.
6. To disconnect the battery charger from the mains
socket, pull the plug. Do not pull the cable.
7. Remove the adapter from the battery charger.
8. Remove the multi battery from the adapter.
Note:
Refer to the multi battery and battery charger
manuals for more information.
To start the product
1. Lift the battery lid.
2. Put a charged battery in battery slot number 1 below
the battery lid. For longer operation time, put a
second charged battery in battery slot number 2.
3. Disconnect the safety key from the safety key holder.
4. Push the safety key into the safety lock. (Fig. 58)
5. Stay behind the product.
6. Push the ON/OFF button on the control panel. The
display comes on.
7. Loosen the start inhibitor. (Fig. 24)
8. Push the motor brake handle in the direction of the
handlebar. (Fig. 59)
Charging status
50%-75%
75%-100%
Fully charged
23