Milwaukee M18 2750-20 Manuel De L'utilisateur page 4

SPECIFICATIONS
Volts.............................................................. 18 DC
Battery Type .................................................M18™
Charger Type................................................M18™
Recommended Ambient
Operating Temperature ......................0°F to 125°F
Cat. No. ..................................................... 2702-20
No Load RPM .......................................Low 0 - 450
BPM ....................................................Low 0 - 7200
Steel ................................................................. 1/2"
Wood
Flat Bit ....................................................... 1-1/8"
Auger Bit .......................................................... 1"
Hole Saw ................................................... 2-1/8"
Screws (dia.)................................................. 1/4"
Masonry ............................................................ 5/8"
Cat. No. ..................................................... 2750-20
RPM ........................................................... 0 - 2800
IPM ............................................................ 0 - 3600
ASSEMBLY
Recharge only with the charger
WARNING
specified for the battery. For spe-
cific charging instructions, read the operator's
manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
Always remove battery pack before
WARNING
changing or removing accessories.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
To reduce the risk of injury, always
WARNING
use a side handle when using a 9.0
Ah or higher capacity battery pack with this tool.
Always brace or hold securely. Ensure side
handle is tightened securely before each use.
Installing the Side Handle
If your drill/driver did not come with a side handle,
visit www.milwaukeetool.com for the appropriate
accessory handle.
1. To install the side handle, loosen
the side handle grip until the
hooks are far enough apart to fit
into the slots on the gear case
ring. Position the side handle on
the top, pointing to the left or
right. Tighten the side handle grip
until it is secure.
2. To remove the side handle,
loosen the side handle grip until
the side handle can be removed. Reposition and
tighten securely.
Only use accessories specifically
WARNING
recommended for this tool. Others
may be hazardous.
Installing Bits
(Cat. No. 2702-20)
Always remove the battery before inserting or remov-
ing bits. Select the proper style and size bit for the job.
This tool is equipped with a spindle lock. The chuck
can be tightened with one hand, creating higher grip
strengths on the bit.
1. To open the chuck jaws, turn the sleeve in the
counterclockwise direction.
When using drill bits, allow the bit to strike the
bottom of the chuck. Center the bit in the chuck
jaws and lift it about 1/16" off of the bottom.
When using screwdriver bits, insert the bit far
enough for the chuck jaws to grip the hex of the bit.
2. To close the chuck jaws, turn the sleeve in the
clockwise direction. The bit is secure when the
chuck makes a ratcheting sound and the sleeve
can not be rotated any further.
High 0 - 1800
3. To remove the bit, turn the sleeve in the counter-
clockwise direction.
High 0 - 28800
NOTE: A ratcheting sound may be heard when the
chuck is opened or closed. This noise is part of the
locking feature, and does not indicate a problem with
the chuck's operation.
WARNING
use on impact wrenches and drivers. Other
sockets and accessories might shatter or break
causing injury.
Attaching and Removing Accessories
This impact driver is intended for use with drill and
driver bits.
1. To attach an accessory, press the shank into the
hex drive chuck.
2. To remove the accessory, pull out the ring and
remove the accessory. Release the ring.
WARNING
ries. Only use accessories specifically recom-
mended for this tool. Others may be hazardous.
To reduce the risk of injury, wear safety goggles
Hooks or glasses with side shields.
The speed selector is on top of the motor housing.
Slots
Allow the tool to come to a complete stop before
changing speeds. See "Applications" for recom-
mended speeds under various conditions.
1. For Low speed, push the speed selector to display
"1".
2. For High speed, push the speed selector to display
"2".
The control switch may be set to three positions: for-
ward, reverse and lock. Due to a lockout mechanism,
the control switch can only be adjusted when the ON/
OFF switch is not pressed. Always allow the motor to
come to a complete stop before using the control switch.
Push for
Forward
4
Use only sockets and other acces-
sories specifically designed for
1/4" Hex Impact Driver
(Cat. No. 2750-20)
OPERATION
Always remove battery pack before
changing or removing accesso-
Selecting Speed
(Cat. No.2702-20)
Using the Control Switch
PUSH TO CENTER TO LOCK
Push for
Reverse