Publicité
Les langues disponibles
Les langues disponibles
Character
L
pA
L
wA
L
pCpeak
K...
h,AG
h,DS
For your safety.
Read all safety warnings and all
WARNING
instructions. Failure to follow the
warnings and instructions may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
Do not use this power tool before you have
thoroughly read and completely understood this
Instruction Manual and the enclosed "General
Safety Instructions" (document number
3 41 30 054 06 1). The documents mentioned should
be kept for later use and enclosed with the power tool,
should it be passed on or sold.
Please also observe the relevant national industrial
safety regulations.
Intended use of the power tool:
Hand-guided, battery-operated angle grinder for dry
grinding, wire brushing and cutting of metal, stainless
steel and stone as well as for cutting tiles in weather-
protected environments with the application tools and
accessories recommended by FEIN.
In environments subject to interference, a reduction of
the operating quality is possible; this can include tem-
porary failure, temporary reduction of the function or
the intended operating behaviour, for the correction of
which intervention by the operator is required.
The power tool is not intended for working plastics and
for polishing. The operator is solely liable for any dam-
age caused by use not as intended for.
Generally recognized accident prevention regulations
and enclosed safety instructions must be observed.
Safety Warnings common for Grinding, Sanding,
Wire Brushing or Abrasive Cutting Off Operations
This power tool is intended to function as a grinder,
sander, wire brush or cut-off tool. Read all safety warn-
ings, instructions, illustrations and specifications pro-
vided with this power tool. Failure to follow all
instructions listed below may result in electric shock,
fire and/or serious injury.
Unit of measurement,
international
kg
kg
dB
dB
dB
2
m/s
2
m/s
2
m/s
m, s, kg, A, mm, V,
W, Hz, N, °C, dB,
2
min, m/s
Explanation
Weight of the power tool without battery and application tool
Weight of the battery
Sound pressure level
Sound power level
Peak sound pressure level
Uncertainty
Vibrational emission value according to EN 60745 (vector sum of
three directions)
Mean vibrational value for angle grinding
Mean vibrational value for sanding with sanding sheet
Basic and derived units of measurement from the international
system of units SI.
Operations such as polishing are not recommended to
be performed with this power tool. Operations for
which the power tool was not designed may create a
hazard and cause personal injury.
Do not use accessories which are not specifically
designed and recommended by the tool manufacturer.
Just because the accessory can be attached to your
power tool, it does not assure safe operation.
The rated speed of the accessory must be at least equal
to the maximum speed marked on the power tool.
Accessories running faster than their rated speed can
break and fly apart.
The outside diameter and the thickness of your acces-
sory must be within the capacity rating of your power
tool. Incorrectly sized accessories cannot be adequately
guarded or controlled.
Threaded mounting of accessories must match the
grinder spindle thread. For accessories mounted by
flanges, the arbour hole of the accessory must fit the
locating diameter of the flange. Accessories that do not
match the mounting hardware of the power tool will
run out of balance, vibrate excessively and may cause
loss of control.
Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for chips
and cracks, backing pad for cracks, tear or excess
wear, wire brush for loose or cracked wires. If power
tool or accessory is dropped, inspect for damage or
install an undamaged accessory. After inspecting and
installing an accessory, position yourself and bystand-
ers away from the plane of the rotating accessory and
run the power tool at maximum no-load speed for one
minute. Damaged accessories will normally break apart
during this testtime.
Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing pro-
tectors, gloves and workshop apron capable of stopping
small abrasive or workpiece fragments. The eye pro-
tection must be capable of stopping flying debris gener-
en
29
Publicité
