EINHELL TE-PS 165 Instructions D'origine page 22

6.2 Using the plunge saw
•
Adjust the cutting depth, cutting angle and
parallel stop (see section 5.1, 5.2 and 5.4)
•
Make sure that the On/Off switch (2) is not
depressed. Only then should you insert the
power plug into a suitable socket outlet.
•
Do not switch on the plunge saw until you
have fitted a saw blade.
•
Place the soleplate on the workpiece you
want to saw. The saw blade must not be in
contact with the workpiece.
•
Hold the plunge saw firmly with both hands.
6.3 Switching On/Off (Fig. 9)
Switching on:
Slide the locking button (3) up and then press the
On/Off switch (2).
•
Allow the saw blade to accelerate until it
reaches full speed. Then slowly move the saw
blade along the cutting line. Only exert gentle
pressure on the saw blade as you do so.
To switch off :
Release the locking button and ON/OFF switch
•
If you release the handle the equipment will
shut down automatically which means that it
cannot operate accidentally.
•
Ensure that you do not cover or block the ven-
tilation openings whilst working with the tool.
•
Do not slow down the saw blade after you
switch it off by pressing it sideways.
•
Important! Do not put down the machine until
the saw blade has reached a complete stand-
still.
Important. Carry out a trial cut in a piece of
waste wood
6.4 Changing the saw blade (Fig. 10-14)
Caution! Always pull out the power plug befo-
re doing any work on the plunge saw!
Use only saw blades which comply with standard
EN 847-1 and are of the same type as the saw
blade supplied with this circular saw. Ask your
dealer for advice.
Use the saw blade key (14) supplied to change
the saw blade. The saw blade key (14) is stored
in the housing. If required, pull the saw blade key
(14) out of the housing (see Figure 10).
Anl_TE_PS_165_SPK9.indb 22 Anl_TE_PS_165_SPK9.indb 22
GB
Caution! The plunge saw must not be opera-
ted with the saw blade key (14) inserted in it.
•
Set the sawing depth to the maximum possib-
le value (see section 5.1)
•
Slide the blade lock for changing the saw bla-
de (21) fully forward (Fig. 11).
•
Slide the locking button for the On/Off switch
(3) up and press the handle down until you
hear it click into place (Fig. 11). The saw
blade will now remain in this position auto-
matically.
•
Now press the spindle lock (12) (Fig. 12).
•
Remove the screw for securing the saw blade
(17) using the saw blade key (14) (Fig. 13).
•
Now remove the flange (18) and the saw bla-
de (13) (Fig. 14).
•
Clean the flange and fit the new saw blade.
Make sure that the direction of rotation is
correct when doing so (see the arrows on the
saw blade and guard hood)!
•
Tighten the screw for securing the saw blade
(17) and check that the blade runs true.
•
Now slide the blade lock for changing the saw
blade (21) fully back. The saw blade will go
down behind the guard hood (19) again.
•
Before you press the On/Off switch, make
sure that the saw blade is correctly fitted and
that moving parts run smoothly and the clam-
ping screws are tightened securely.
7. Replacing the power cable
Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
- 22 -
21.12.2022 09:42:32 21.12.2022 09:42:32