SCHOLTES TIS 842 Mode D'emploi page 22

N = Timer Buttons
GB
N1 = Tenths display
N2 = Units display
O = Hob indicator with timer function active
Q = Timerz Display
R = Cooking zone display
R1 = Active cooking zone indicator
S = Booster
- To start the hob, press the button (A), on all displays (R)
the zeros will appear for 20 seconds with flashing decimal
points.
If no operation is performed within this time period, the
hob switches off.
- It is possible to switch a cooking zone on by selecting
one of the 4 buttons (E). The cooking zone is active when
the decimal point becomes fixed.
Set the desired cooking level by acting on the SLIDER
control (D1).
Note: to set the cooking level, just slide your finger over
the SLIDER control (D1).
From Left to Right the temperature level is increased
(D2) from 1 to 9. To decrease just perform the operation
in the reverse order.
The cooking level (e.g. 6) will appear on the cooking zone
display (R).
Note: you may also directly press any point on the
SLIDER control without running your finger along it; in
this case the temperature level corresponding to the
point at which the control was touched will be activated
directly.
- There are several different ways of switching off a cook-
ing zone:
1- Select it and run your finger over the SLIDER control
until you reach "0".
2- Select it and directly press the "-" symbol on the SLIDER
control.
- When a cooking zone (E) is switched to the OFF setting
and the temperature of the glass surface remains above
approximately 50°, the display (R) corresponding to that
zone will show a luminous signal alternating between "0"
and "H".
- If the hob is switched to the OFF setting (A), the luminous
signal will display the letter "H" in a fixed manner.
Warning:
To prevent damage being inflicted on the electronic cir-
cuits, the hob is fitted with an overheating safety system.
In situations where the appliance is used at high power
levels for a prolonged period of time, the hob may switchoff
one or more of the activated zones temporarily, until the
temperatures return to the set levels.
On the display corresponding to the cooking zone which
has been temporarily switched off, the power level will be
shown in alternation with a E/2.
22
All manuals and user guides at all-guides.com
This will stop flashing once the cooking zone has been-
reactivated.
• Key function:
To keep children or persons needing supervision from
using the hob surface, all of the functions can be blocked
in the following way:
1- Switch to hob on (if it is off) by selecting the "ON/OFF"
key. The cooking zones must be off.
2- Press the "S" key and the R4 (Fig.2).
3- Press only the cooking zone R4 (Fig.2).
The "L" letter indicating that the function is active will ap-
pear on the display.
Should one or more zones still be hot, the letter "H" and
"L" will alternate on the relative displays.
- To deactivate the key function, switch the hob off (if
it is on) by selecting the "ON/OFF" key.
- Once it is off, switch the hob back on.
- Press the "S" key and the R4 (Fig.2).
- Press the"S" key a second time.
- Zeros will appear on all the displays for a few seconds.
- If the cooker top is switched off with the KEY function
active, when subsequently activated the top will be in the
same situation, meaning with the KEY function active.
- If the hob is switched on and the Lock function is enabled,
button ON/OFF will still work.
• Magnetic sensor:
- The hob is equipped with a pan sensor; when the pan is
removed or badly positioned, the
If, on the other hand, the surface of the glass is still hot,
the symbol will appear alternating with the .
• O.S.D. (Overflow Safety Device):
The hob is equipped with a safety system which moves all
hotplates to the OFF position and activates the safety lock
when liquids or items are detected on the control panel.
These symbols will flash on the display:
can be deactivated by removing the item or the liquid. The
hob will switch off automatically.
• Attention!
When the hob switches on, the timer display Q stays on
at the value . If the function is not activated, after a few
seconds the display Q shows nothing.
• Timer (Fig.2 (Q)):
Note: the Timer can be activated on all the cooking zones
simultaneously.
This function allows to establish the time (from 1 to 99 min-
utes) or automatic switch-off of the cooking zone selected.
Activation:
1- Select the cooking zone (E).
2- Set the cooking level (from 1 to 9) desired, by acting on
symbol will appear.
. They