Publicité
Les langues disponibles
Les langues disponibles
Package contents
The package contains:
1 Partly assembled machine
1 Table
1 Rip fence
1 Mitre fence
1 Box containing:
1 legstand (4 legs 530 mm, 2 traverse rails 480 mm, 2 traverse rails
360 mm, M5 x 16 bolts, M5 nuts and M5 washers for assembling
the legstand, M8 x 20 bolts and washers for mounting the machine
onto the legstand)
1 spanner 10/13 mm
1 Allen key 2.5 mm
1 Instruction manual
1 Exploded drawing
• Check for damage to the tool, parts or accessories which may have
occurred during transport.
• Take the time to thoroughly read and understand this manual prior to
operation.
• Remove the saw from the packaging material carefully.
• Study figure A to become familiar with the terminology used to
describe the various parts of the saw.
Description (fig. A)
Your DW876 bandsaw has been designed for professional workshop
applications: it performs straight, circular, mitre and bevel cuts. It can cut a
wide range of materials such as wood, plastics, non-ferrous metals and
leather.
1 ON/OFF-switch
2 Blade
3 Blade guard
4 Table
5 Rip fence
6 Mitre fence
7 Legstand
8 Blade tensioner
9 Door lock
10 Blade tension scale
11 Bevelling table support
12 Locking lever
13 Motor positioning bolt
14 Blade centring adjuster
15 Blade guard height adjuster
16 Dust extraction adapter
Electrical safety
The electric motor has been designed for one voltage only. Always check
that the power supply corresponds to the voltage on the rating plate.
Mains plug replacement (U.K. & Ireland only)
• Should your mains plug need replacing and you are competent to do
this, proceed as instructed below. If you are in doubt, contact an
authorized D
WALT repair agent or a qualified electrician.
E
• Disconnect the plug from the supply.
• Cut off the plug and dispose of it safely; a plug with bared copper
conductors is dangerous if engaged in a live socket outlet.
• Only fit 13 Amperes BS1363A approved plugs fitted with the correctly
rated fuse (1).
• The cable wire colours, or a letter, will be marked at the connection
points of most good quality plugs. Attach the wires to their respective
points in the plug (see below). Brown is for Live (L) (2) and Blue is for
Neutral (N) (4).
• Before replacing the top cover of the mains plug ensure that the cable
restraint (3) is holding the outer sheath of the cable firmly and that the
two leads are correctly fixed at the terminal screws.
13
All manuals and user guides at all-guides.com
Using an extension cable
If an extension cable is required, use an approved extension cable suitable
for the power input of this tool (see technical data). The minimum
conductor size is 1.5 mm
When using a cable reel, always unwind the cable completely.
Also refer to the table below.
Conductor size (mm
0.75
1.00
1.50
2.50
4.00
Voltage
220/240
Assembly and adjustment
• The machine is fully assembled except for the legstand and table top.
Assembling the legstand (fig. B)
The legstand components and fasteners are packed separately.
• Assemble the legs and traverse rails using the nuts, bolts and washers
• Ensure that the plastic feet are all facing downwards. The assembled
• Place the machine on the legstand, making sure that the machine base
• Secure the machine to the legstand using the nuts, bolts and washers
• Firmly tighten all the bolts.
Mounting the table top (fig. C)
• Make sure that the bevelling table support (11) is in horizontal position
• With the scale (17) to the front, install the table top on the bevelling
Never use a light socket.
Never connect the live (L) or neutral (N) wires to the earth pin
marked E or
.
2
.
2
)
Cable rating (Amperes)
6
10
15
20
25
Cable length (m)
7.5
15
25
Amperes
Cable rating (Amperes)
0 - 2.0
6
6
6
2.1 - 3.4
6
6
6
3.5 - 5.0
6
6
6
5.1 - 7.0
10
10
10
7.1 - 12.0
15
15
15
12.1 - 20.0
20
20
20
Prior to assembly and adjustment always unplug the tool.
as shown. Do not yet tighten all the way.
frame is shown in figure A.
fits over the legstand on all four sides.
supplied with the tool.
The machine must be level and stable at all times.
and that the lever (12) is locked.
table support (11) using the four bolts.
E N G L I S H
30
45
60
6
6
6
6
6
6
6
10
15
10
15
15
15
20
20
20
25
-
en - 3
Publicité
