Technical Characteristics; Dimensions And Weight; Operating Instructions; Water Temperature - Interpump Group SS71 Manuel D'utilisation Et D'entretien

5

TECHNICAL CHARACTERISTICS

Model Rpm
SS 7193 1000
SS 71106 1000
800
SS 71153 900
1000
SS 71170
900
SS 71170-F
Model Rpm
SN 7193 1000
SN 71106
1000
SN 71106-F
800
SN 71153
900
SN 71153-F
1000
SN 71170
900
SN 71170-F
Model Rpm
SW71170 900
6

DIMENSIONS AND WEIGHT

For Standard SS-SN-SW version pump dimensions and weight, refer to Fig. 2.
Dry weight 68 kg.
7

OPERATING INSTRUCTIONS

SS71 pumps, when not ordered with the ATEX configuration,
have been designed to operate in environments with
atmospheres that are not potentially explosive, with filtered
water (see par. 9.7) at a maximum temperature of 85°C,
with the head and all the components in contact with the
fluid made of AISI 316L, plus special high and low pressure
energized seals. SN71 pumps, when not ordered with the
ATEX configuration, have been designed to operate in
environments with atmospheres that are not potentially
explosive, with filtered water (see par. 9.7) and at a
maximum temperature of 85°C, with the head made of AISI
420 and all the components in contact with the fluid made
of AISI 316L plus special high and low pressure energized
seals. The SW71 pumps have been designed to operate in
environments with atmospheres that are not potentially
explosive, with filtered sea water (see par. 9.7) at a maximum
temperature of 85°C, with the head and all the components
in contact with the fluid made of AISI 316L, plus special high
and low pressure energized seals. Other liquids can be used
only upon formal approval by the Technical or Customer
Service Department.
Flow rate
l/min Gpm
93 24.5
106 28.0
122 32.2
137 36.2
153 40.5
170 44.9
Flow rate
l/min Gpm
93 24.5
106 28.0
122 32.2
137 36.2
153 40.5
170 45
Flow rate
l/min Gpm
170 44.9
7.1
7.2
The rated specifications stated in our catalog are the max.
that can be obtained by the pump. Independently of the
power used, the maximum pressure and rpm indicated on the
specification label can never be exceeded unless prior formal
authorization is given by our Technical or Customer Service
Departments.
7.3
The minimum speed allowed for these types of pumps
is 100 rpm for non-continuous periods; any rpm other
than mentioned and shown in the performance table (see
chapter 5) must be expressly and formally authorized by the
Engineering Department or Customer Service.
23
Pressure
bar psi
200 2900 35.3
200 2900 40.4
160 2320
140 2030
130 1885
100 1450
Pressure
bar psi
210 3045 37.5
200 2900 40.4
160 2320
140 2030
130 1885
110 1600
Pressure
bar psi
100 1450 32.5

Water temperature

The permissible water temperature is 40°C.
However, the pump can be used with water up to a
temperature of 85°C.
In this case, it is best to consult the Technical or
Customer Service Departments.

Maximum pressure and flow rate

Minimum operating speed

Power
kW HP
48
55
37.5 51
36.8 50
38.2 52
32.5 44.2
Power
kW HP
51
55
37.5 51
36.8 50
38.2 52
36 49
Power
kW HP
44.2
Fig. 2