Inventum VWM9001B Mode D'emploi page 44

WASHING MODE
NORMAL CARE (basic/default setting)
No button lit.
INTENSIVE [intensief] (This mode will save energy; washing time will be longer,
and water consumption will be lower.)
SHORT [kort] (This mode will save time as programme duration will be shorter, STEAM CLEAN
but it will use more water.)
i
• The light on the button for the selected washing mode is lit.
RPM [toeren] (SPINNING RATE/DRAIN/PUMP STOP)
For changing the spinning rate, only draining, and pump stop. With a preset or
selected spinning rate, the spinning rate number will light up on the display unit.
If you select draining without spinning, the symbol
unit. If you select Pump stop, the symbol
STEAM CLEAN
Select the Pump stop
water from the last rinse cycle in order to prevent it from creasing when you are unable to take it from the washing machine
immediately after the washing programme is complete. You may set the desired spinning rate. To continue the programme,
press the Start/Pause button that is lit. Water will be drained (pumped out) and the final spin cycle will run.
CHILD LOCK (RPM [toeren] and Start Delay [startuitstel])
A safety feature. To activate the child lock, simultaneously press RPM [toeren] and Start Delay [startuitstel] and hold
them for at least three seconds. The selection will be confirmed by an acoustic signal and by a signal light (the symbol
will be lit). Follow the same procedure to deactivate the child lock. As long as the child lock is activated, programme, settings,
or additional functions cannot be changed.
Child lock remains active even after the washing machine is switched off. For safety reasons, the child lock does not prevent
switching off the washing machine with the On/Off/Reset button. To select a new programme, the child lock must first be
deactivated.
Start Delay [startuitstel]
Use this function to start the washing cycle after a certain amount of time has elapsed. Press Start Delay [startuitstel]
and -:-- will appear on the display. If, for example, you choose a programme with a duration of 2:39, the time will be indicated
on the display unit, and the symbol
If the function Start Delay has been selected, the symbol
By pressing Start Delay [startuitstel], you can adjust the time in 30-minute steps up to 6 hours, and by 1-hour steps up to
24 hours.
If nothing is pressed for 5 seconds, the actual washing time will be displayed. To set the time to the end of the washing
programme again, press Start Delay.
The function is activated when the Start/Pause button is pressed. The washing machine will count down the set time. When
the countdown reaches zero, the selected washing programme will start automatically.
• To interrupt or change the start delay time, press and hold the On/Off/Reset button. Press Start Delay [startuitstel] to
select a new delay time and confirm it by pressing the Start/Pause button.
• To quickly cancel the start delay, press and hold Start Delay [startuitstel] for 3 seconds. The washing programme will
resume.
• In case of a power supply failure before the delay time has elapsed, press the Start/Pause button to resume the delay
time countdown.
EXTRA WATER [extra water] (HIGH WATER LEVEL)
Use this function to wash with a larger amount of water, and with two additional rinse cycles on some programmes.
44
• English
auto programma
60° allergie
40° overhemden
30° wol
30° extra kort 20 min.
eco 40 - 60
centrifugeren / afpompen
spoelen +
reset
3 sec.
trommelreiniging
auto programma
60° allergie
40° overhemden
30° wol
30° extra kort 20 min.
eco 40 - 60
will appear on the display unit.
centrifugeren / afpompen
spoelen +
reset
option when you want the laundry to stay soaked in the 3 sec.
trommelreiniging
will be lit under the time.
katoen 90°
60°
40°
30°
20°
mix 40°
30°
toevoegen
katoen 90°
60°
40°
30°
will appear on the display
20°
mix 40°
30°
toevoegen
will be lit.
intensief
voorwas toeren
was
intensief
voorwas toeren
was
kort extra water
startuitstel
kort extra water
startuitstel