OEM HENERGO HV/45 E-1 Mode D'emploi Et D'entretien page 34

G45
General specifi cations and warning
CHAPTER
.......................................................
Chapter for the technician and operator
1.1 GENERAL WARNINGS ..................................... Page EN-3
1.2 REFERENCE NORMATIVES ............................ Page EN-4
1.3 DESCRIPTION OF THE SYMBOLS .................. Page EN-4
1.4 MACHINE COMPOSITION ................................ Page EN-4
1.5 PREARRANGEMENTS
AT PURCHASER'S CHARGE ............................ Page EN-5
1.6 EMERGENCY OPERATIONS
IN CASE OF FIRE .............................................. Page EN-5
1.7 EXPLOSION RISK ............................................. Page EN-5
1.8 ACOUSTIC PRESSURE LEVEL ....................... Page EN-5
CHAPTER
.......................................................
Chapter for the technician
- OVERALL DIMENSIONS ........................................ Page EN-6
2.1 TECHNICAL SFEATURES .............................. Page EN-7
2.2 TRANSPORT ..................................................... Page EN-8
2.2.a Shipment ................................................... Page EN-8
2.2.b Lifting of the packing ................................. Page EN-8
2.2.c Storage ...................................................... Page EN-8
2.3 RECEPTION OF THE MACHINE ....................... Page EN-9
2.4 UNPACKING ...................................................... Page EN-9
2.5 IDENTIFICATION OF THE COMPONENTS .... Page EN-10
2.6 IDENTIFICATION OF THE MACHINE ............. Page EN-10
CHAPTER
.......................................................
Chapter for the technician
3.1 LIFTING OF THE MACHINE ............................ Page EN-11
3.2 COMPONENTS' ASSEMBLY ...................... Page EN-11
3.3 ELECTRICAL CONNECTION ......................... Page EN-12
3.3.a Electric oven connection ......................... Page EN-12
3.3.b Unipotential connection ......................... Page EN-13
3.4 OVEN POSITIONNING .................................... Page EN-13
3.5 FIRST STARTING ............................................ Page EN-13
3.6 INVERSION OF BELT ROTATION'S
DIRECTION ..................................................... Page EN-14
3.7 INSTALLATION OF OPTIONAL
SUPPORTING SURFACE ............................ Page EN-14
3.8 INSTALLATION OF AN OPTIONAL
ROLLER UNIT ............................................... Page EN-14
CHAPTER
.......................................................
Chapter for the technician and operator
4.1 EXPECTED USE ............................................ Page EN-15
4.2 INCORRECT USE ......................................... Page EN-15
4.3 SAFETY PLATES ........................................... Page EN-15
4.4 SAFETY DEVICES ......................................... Page EN-16
4.5 OPERATOR'S AREAS ................................... Page EN-16
4.6 RESIDUAL DANGER AREAS ....................... Page EN-16
4.7 DANGEROUS AREAS ................................... Page EN-16
1
CHAPTER
.......................................................
Chapter for the technician and operator
5.1 CONTROL BOARD ........................................ Page EN-17
5.2 RUNNING ........................................................ Page EN-18
5.3 SETTINGS MODIFICATION .......................... Page EN-19
5.4 ADJUSTMENT OF THE OVEN'S
OPENING HEIGHT ......................................... Page EN-19
5.5 ALARMS DURING RUNNING ....................... Page EN-20
5.5.a Damaged or disconnected
temperature detector alarm ....................Page EN-20
5.5.b Belt motor alarm .................................... Page EN-20
5.5.c Overheating alarm ................................. Page EN-20
5.6 TURNING OFF ............................................... Page EN-20
5.7 FAILURE, CAUSES AND REMEDIES .......... Page EN-21
2
CHAPTER
.......................................................
Chapter for the technician and operator
6.1 ROUTINE AND PLANNED
MAINTENANCE ............................................. Page EN-22
6.1.a In general .............................................. Page EN-22
6.1.b Ordinary maintenance ......................... Page EN-22
6.1.b - a Outer cleaning ................................ Page EN-22
6.1.b - b Oven's internal cleaning ............... Page EN-22
6.1.c Planned maintenance .......................... Page EN-24
6.1.c - a Every 2 years ................................. Page EN-24
6.1.d Maintenance in case of need .............. Page EN-24
6.1.d - a Belt tightening ................................. Page EN-24
3
CHAPTER
.......................................................
Chapter for the technician
7.1 DISMANTLING THE MACHINE .................... Page EN-25
7.2 DEMOLISHING THE MACHINE .................... Page EN-25
7.3 DISPOSING OF HARMFUL SUBSTANCES Page EN-25
220 SINGLE-PHASE MOTOR WIRING DIAGRAM ..... Page EN-26
230 THREE-PHASE MOTOR WIRING DIAGRAM...... Page EN-27
400 THREE-PHASE MOTOR WIRING DIAGRAM...... Page EN-28
LEGENDA .............................................................. Page EN-29
4
ENGLISH
5
6
7
EN - 1