Ryobi RBS904 Mode D'emploi page 15

WARNING
If any parts are damaged or missing do not operate
this product until the parts are replaced. Use of this
product with damaged or missing parts could result in
serious personal injury.
WARNING
Do not attempt to modify this tool or create accessories
not recommended for use with this tool. Any such
alteration or modifi cation is misuse and could result
in a hazardous condition leading to possible serious
personal injury.
WARNING
Do not connect to power supply until assembly is
complete. Failure to comply could result in accidental
starting and possible serious personal injury.
MOUNTING BAND SAW TO WORKBENCH
If the band saw is to be used in a permanent location,
the band saw must be mounted to a fi rm supporting
surface such as a workbench. Four bolt holes have been
provided in the saw's base for this purpose. Bolts (not
included) should be of suffi cient length to accommodate
the saw base, lock washers (not included), hex nuts (not
included), and the thickness of the workbench. Tighten
all four bolts securely.
Carefully check the workbench after mounting to
make sure that no movement can occur during use.
If any tipping, sliding, or walking is noted, secure the
workbench to the fl oor before operating.
■
Place band saw on the workbench. Using the saw
base as a pattern, locate and mark the holes where
the band saw is to be mounted.
■
Drill holes through the workbench.
■
Place band saw on the workbench aligning holes in
the saw base with the holes drilled in the workbench.
■
Insert bolts (not included) and tighten securely
with lock washers and hex nuts (not included).
NOTE: all bolts should be inserted from the top.
Install the lock washers and hex nuts from the
underside of the bench.
CLAMPING BAND SAW TO WORKBENCH
See Figure 4.
If the band saw is to be used as a portable tool, it is
recommended that you fasten it permanently to a
mounting board that can easily be clamped to a
workbench or other supporting surface. The mounting
board should be of suffi cient size to avoid tipping of saw
while in use. Any good grade plywood or chipboard with
a 19 mm (3/4") Thickness is recommended.
If lag bolts are used, make sure they are long enough to
go through holes in the saw base and material the saw
is being mounted to. If machine bolts are being used,
make sure bolts are long enough to go through holes in
the saw base, the material being mounted to, and the
lock washers and hex nuts.
NOTE: it may be necessary to countersink hex nuts and
washers on bottom side of mounting board.
■
Mount saw to board using holes in saw base as a
template for hole pattern. Locate and mark the holes
where the band saw is to be mounted.
■
Follow the last three steps in the section Mounting
Band Saw to Workbench, shown above.
MOUNTING THE SAW TABLE
See Figures 5, 7.
■
Remove the d-nut, washers, and wing screw on the
saw table.
■
Standing at the front of the band saw, slide the saw
table past the blade and through the slot moving
from the right side of the saw table to the left.
■
Holding the saw table with your left hand while
pulling the angle adjustment knob away from the
saw frame, align the teeth on the saw table bracket
into the teeth on the angle adjustment knob. Release
the knob.
■
Fit the pins on the frame into the slots of the saw
table bracket.
■
Insert the washer on the threaded end of the table
lock lever. Tighten the saw table to the saw frame by
turning the table lock lever clockwise.
■
Attach the d-nut, washers, and wing screw to the
saw table.
NOTE: the wing screw goes below the saw table.
INSTALLING EXTENSION SUPPORT
See Figure 6.
■
Insert the tubes of the extension support into the
holes in the saw base from the rear.
■
Align the holes on the tubes and those on the saw
base.
■
Insert locking bolts and tighten with washers and hex
nuts.
SQUARING THE SAW TABLE TO THE BLADE
See Figures 8 - 9.
■
Turn the lock knob counterclockwise to unlock the
blade guide assembly. Turning the blade guide
adjustment knob clockwise, raise the blade guide
assembly as far as it will go. Turn the lock knob
clockwise to retighten.
■
Place a small combination square on the saw table
beside the blade.
■
Loosen the table lock lever and rotate the angle
adjustment knob to tilt the saw table up or down to
align table 90° to blade (0° position). Retighten the
table lock lever.
■
Turn the adjusting bolt until the bolt just touches the
saw housing.
■
Check squareness of the saw table to the blade.
Make readjustments if necessary.
Original Instructions
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL
15