Publicité
Les langues disponibles
Les langues disponibles
English
2. To select Speed 2 (high speed setting), turn the tool off
and permit it to stop. Slide the speed selector back (away
from the chuck).
3. If the tool does not change speeds, confirm that the
speed selection switch is completely engaged in the
forward or back position.
Mode Selection (Fig. H)
The mode selection collar
the correct operating mode depending upon the
planned application.
To select, rotate the collar until the desired symbol aligns
with the arrow.
WARNING: When the mode selection collar is in the
drill or hammerdrill positions, the drill will not clutch.
The drill may stall if overloaded, causing a sudden twist.
symbol
1-15
Screwdriving (higher number = greater torque)
symbol
1-15
Screwdriving (higher number = greater torque)
Installing and Removing the Battery Pack
(Fig. I)
WARNING: Ensure the tool/appliance is in the off
position before inserting the battery pack.
nOTE: For best results, make sure your battery pack is
fully charged.
1. To install the battery pack
the battery pack with the rails inside the tool's handle
and slide it into the handle until the battery pack is firmly
seated in the tool and ensure that it does not disengage.
2. To remove the battery pack from the tool, press the
battery pack release button
pack out of the tool handle. Insert it into the charger as
described in the charger section of this manual.
Proper Hand Position (Fig. A, J)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main
handle
3
and the other hand holding the battery pack
Variable Speed Trigger and Forward/
Reverse Control Button (Fig. A)
The tool is turned on and off by pulling and releasing the
variable speed trigger
4
. The farther the trigger is depressed, the
10
6
can be used to select
DCD793
Mode
Drilling
DCD798
Mode
Drilling
Hammerdrilling
1
into the tool handle, align
2
and firmly pull the battery
higher the speed of the tool. Your tool is equipped with a brake.
The chuck will stop as soon as the trigger switch is fully released.
A forward/reverse control button
rotational direction of the tool and also serves as a
lock‑off button.
•
To select forward rotation (clockwise), release the trigger
and depress the forward/reverse control button on the
right side of the tool.
•
To select reverse (counterclockwise), depress the forward/
reverse control button on the left side of the tool.
nOTE: The center position of the control button locks the
tool in the off position. When changing the position of the
control button, be sure the trigger is released.
nOTE: Continuous use in variable speed range is not
recommended. It may damage the switch and should
be avoided.
nOTE: The first time the tool is run after changing the
direction of rotation, you may hear a click on start‑up. This is
normal and does not indicate a problem.
Worklight (Fig. A)
The worklight
8
depressed, and will automatically turn off 20 seconds after
the trigger switch is released. If the trigger switch remains
depressed, the worklight will remain on.
nOTE: The worklight is for lighting the immediate work
surface and is not intended to be used as a flashlight.
Performing an Application (Fig. A)
WARNING: To reduce the risk of personal
injury, ALWAYS ensure workpiece is anchored or
clamped firmly.
WARNING: Always wait until the motor has come to
a complete standstill before changing the direction
of rotation.
Prior to Performing Work
•
Set the speed selector
•
Install the appropriate bit or accessory into the chuck.
Refer to accessory installation instructions in this manual.
WARNING:
•
Do not use this tool to mix or pump easily
combustible or explosive fluids (benzine, alcohol, etc.).
•
Do not mix or stir flammable liquids
labeled accordingly.
Screwdriving
Your tool has a clutch with adjustable torque for driving
and removing a wide array of fastener shapes and sizes. The
numbers 1–15 on the mode selection collar
set a torque range for screwdriving. The higher the number
on the collar, the higher the torque and the larger the
fastener which can be driven.
1
.
1. Turn the mode selection collar to the desired position.
Refer to Mode Selection.
2. Pull the trigger switch applying pressure in a straight line
with the bit until the fastener is seated at the desired
depth in the workpiece.
5
determines the
is activated when the trigger switch is
7
. Refer to Speed Selection.
6
are used to
Publicité
