Publicité
Les langues disponibles
Les langues disponibles
1. Remove the battery pack
•
When not in use
•
Before moving from one place to another
•
Before servicing
•
Before changing accessories or attachments,
such as saw chain and guard
2. Inspect pruning saw before and after each use.
Check saw closely if guard or other part has been
damaged. Check for any damage that may affect
operator safety or operation of saw. Check for
alignment or binding of moving parts. Check for
broken or damaged parts. Do not use pruning
saw if damage affects safety or operation. Have
damage repaired by authorized service center.
To locate an authorized service center, visit www.
worx.com.
3. Maintain pruning saw with care.
•
Never expose saw to rain or direct moisture.
•
Keep chain sharp, clean, and lubricated for better
and safer performance.
•
Follow steps outlined in this manual to sharpen
chain.
•
Keep handles dry, clean, and free of oil and
grease.
•
Keep all screws and nuts tight.
4. When servicing, use only identical replacement
parts.
5. When not in use, always store pruning saw
•
in a high or locked place, out of children's reach
•
in a dry place
•
with Bar and Housing-Cover in place
Bar Maintenance
To maximize bar life, the following bar maintenance
is recommended.
The bar rails that carry the chain should be cleaned
before storing the tool or if the bar or chain appear to
be dirty.
The rails should be cleaned every time the chain is
removed.
To clean the Bar rails.
1. Remove Housing-Cover and bar and chain. (see
section ASSEMBLY)
2. Using a wire brush, screwdriver or similar tool,
clear the residue from the inner groove of the bar.
(See Fig. R)
3. Make sure to clean oil passages thoroughly.
Conditions which require Chain and Guide Bar
maintenance:
•
Saw cuts to one side or at an angle.
•
Saw has to be forced through the cut.
•
Inadequate supply of oil to the bar and chain.
Check the condition of the Guide Bar each time the
chain is sharpened. A worn Guide Bar will damage the
chain and make cutting difficult.
After each use, remove the battery pack, clean all
sawdust from the Guide Bar and sprocket hole.
Cordless Pruning Saw
When rail top is uneven, use a flat file to restore
square edges and sides.
File Rail Edges and
Sides
Square
Worn Groove
Replace the Guide Bar when the groove is worn, the
Guide Bar is bent or cracked, or when excess heating
or burring of the rails occurs. If replacement is
necessary, use only the Guide Bar specified for your
saw in the repair parts list or on the decal located on
the pruning saw.
Replacing Bar & Chain
Replace chain when cutters are too worn to sharpen
or when chain stops. Only use replacement chain
noted in this manual.
Inspect Guide Bar before sharpening chain. A worn
or damaged Guide Bar is unsafe. A worn or damaged
Guide Bar will damage chain. It will also make cutting
harder.
SHARPENING SAW CHAIN
WARNING:
Remove the battery pack before servicing.
Severe injury or death could occur from
electrical shock or body contact with moving
chain.
Cutting edges on chain are sharp. Use protective
gloves when handling chain.
Keep chain sharp. Your saw will cut faster and more
safely. A dull chain will cause undue sprocket, Guide
Bar, chain, and motor wear. If you must force chain
into wood and cutting creates only sawdust with few
large chips, chain is dull.
FOR BATTERY TOOLS
The ambient temperature range for the use and
storage of tool and battery is 0
°F).
The recommended ambient temperature range for
the charging system during charging is 0
(32 °F - 104 °F).
8. TROUBLESHOOTING TABLE
The following table gives checks and actions that
you can perform if your machine does not operate
correctly. If these do not identify/remedy the
problem, contact your service agent.
WARNING: Switch off and remove the battery
pack before investigating fault.
Correct Groove
21
o
o
C-45
C (32 °F - 113
o
o
C-40
C
EN
Publicité
