Publicité
Les langues disponibles
Les langues disponibles
at full speed. Stop the saw by releasing the On/off
Switch. Make sure the chain has stopped before
setting the saw down.
(7) Keep practicing on scrap logs in a secure working
area until you are comfortable, using a fluid
motion and a steady cutting rate.
Kickback Safety Devices On This Saw
This saw has a low-kickback chain and reduced
kickback Guide Bar. Both items reduce the chance
of kickback. However, kickback can still occur with
this saw.
The following steps will reduce the risk of kickback.
•
Keep all safety items in place on saw. Make sure
they work properly.
•
Do not overreach or cut above shoulder height.
•
Keep solid footing and balance at all times.
•
Stand slightly to the left side of saw. This keeps
your body from being in direct line with chain.
•
Do not let Guide Bar nose touch anything when
chain is moving.
•
Never try cutting through two logs at same time.
Only cut one log at a time.
•
Do not bury the Guide Bar nose or try plunge cut
(boring into wood using Guide Bar nose).
•
Watch for shifting of wood or other forces that
may pinch chain.
•
Use extreme caution when reentering a previous
cut.
•
Use only the low-kickback chain and Guide Bar
that were supplied with this pruning saw or
recommended.
20
•
Never use a dull or loose chain. Keep chain sharp
with proper tension.
How to Use Saw Safely
1. Use the pruning saw only with secure footing.
2.
Hold the pruning saw at the right-hand
side of your body (See Fig. L).
3. The Chain must be running at full speed before it
makes contact with the wood.
4. Use the Base Plate to secure the saw onto the
wood before starting to cut.
5. Use the Base Plate as a leverage point while
cutting. (See Fig. M)
6. Raise the Chain Guard when cutting from bottom
to top of material. (See Fig. N)
7. Do not operate the saw with arms fully extended,
attempt to saw areas which are difficult to reach,
or stand on a ladder while sawing. (See Fig. O)
Never use the pruning saw above shoulder
height.
Cutting Wood under Tension (See Fig. P)
WARNING: When cutting a limb that is
under tension, use extreme caution. Be
alert for wood springing back. When wood
tension is released, limb could spring back and
strike operator causing severe injury or death.
Cordless Pruning Saw
When sawing logs supported on both ends, start
the cut from above(Y) about 1/3 of the diameter into
the log (overbuck) and then finish the cut (Z) from
below, in order to avoid contact of the pruning saw
with the ground. When sawing logs supported on
only one end, start the cut from below (Y) about 1/3 of
the diameter into the log (underbuck) and finish the
cut from above (Z) in order to avoid log splitting or
jamming of the pruning saw.
OPERATION FOR POLE SAW
Cutting with extension pole
1. Install the battery pack into the machine.
2. Before cutting a high branch, consider all the
same points detailed in the previous section
"Trimming Branches" but pay particular attention
to the likely path of the falling branch.
WARNING: Do not stand directly below a branch
being cut. Keep bystanders far away. Do not
stand on a ladder or other type of unstable
support while using the tool. Do not use the tool
near cable, electrical power or telephone lines.
Keep 3m away from all power lines. (See Fig.
Q1-Q4)
3. Use both hands to grip Pole Saw. Use only
designated grip areas when operating Pole Saw
(See Fig. Q5). Use firm grip. Thumbs and fingers
must wrap around Pole Saw handle and pole.
4. Make sure your footing is firm. Keep feet apart.
Divide your weight evenly on both feet.
5. When ready to make a cut, press the Lock-out
Button, then fully press the On/off Switch (See
Fig. Q6). This will turn Pole Saw on. Releasing On/
off Switch will turn Pole Saw off. Make sure saw is
running at full speed before starting a cut.
6. When starting a cut, place moving chain
against wood. Hold Pole Saw firmly in place to
avoid possible bouncing or skating (sideways
movement) of saw.
7. Guide Pole Saw using light pressure. Do not force
Pole Saw. The motor will overload and can burn
out. It will do the job better and safer at the rate
for which it was intended.
8. Remove Pole Saw from a cut with saw running
at full speed. Stop Pole Saw by releasing trigger.
Make sure chain has stopped before setting Pole
Saw down.
7. SAW MAINTENANCE
Follow maintenance instructions in this manual.
Proper cleaning of saw and chain and Guide Bar
maintenance can reduce chances of kickback.
Inspect and maintain saw after each use. This will
increase the service life of your saw.
NOTE: Even with proper sharpening, risk of kickback
can increase with each sharpening.
MAINTENANCE AND STORAGE OF PRUNING SAW
EN
Publicité
