Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
eXtenSion CordS
grounded tools require a three wire extension cord
either a two or three wire extension cord. As the distance from the power supply outlet increases, you must use a
heavier gauge extension cord. using extension cords with inadequately sized wire causes a serious drop in voltage,
resulting in loss of power and possible tool damage. Refer to the table shown below to determine the required
minimum wire size.
The smaller the gauge number of the wire, the greater the capacity of the cord. for example: a 14-gauge cord
can carry a higher current than a 16-gauge cord. When using more than one extension cord to make up the total
length, be sure each cord contains at least the minimum wire size required. If you are using one extension cord for
more than one tool, add the nameplate amperes and use the sum to determine the required minimum wire size.
guidelines for using extension Cords
• If you are using an extension cord outdoors, be sure it is marked with the suffix "W-A" ("W" in Canada) to
indicate that it is acceptable for outdoor use.
• Be sure your extension cord is properly wired and in good electrical condition. Always replace a damaged
extension cord or have it repaired by a qualified person before using it.
• Protect your extension cords from sharp objects, excessive heat, and damp or wet areas.
Recommended Minimum Wire Gauge for Extension Cords (120 Volt)
Nameplate
Extension Cord Length
Amperes
25 Feet
(At Full Load)
0–2.0
18
2.1–3.4
18
3.5–5.0
18
5.1–7.0
18
7.1–12.0
18
12.1–16.0
14
16.1–20.0
12
SPECIFIC SAFETY RULES FOR MITER SAWS
wArning:
FroM repeAted uSe) repLACe StriCt AdHerenCe to produCt SAFetY ruLeS. if
you use this tool unsafely or incorrectly, you can suffer serious personal injury!
do not operate this miter saw
•
if you are not thoroughly familiar with the operation of miter saws
•
guidance from your supervisor, instructor, or other qualified person.
Mount the tool securely to a stable supporting surface prior to operation
•
Ideally, firmly clamp or bolt your miter saw to a workbench, table, or tool stand at approximately hip height.
use the guards whenever possible
•
and working properly.
use only crosscut saw blades.
•
carbide tipped blades.
easily deflect and contact the guard or miter saw table.
use only blades that are the correct size and type specified for this tool.
•
Be sure to use a sharp blade
•
inspect blades for cracks or other damage
•
damaged blade immediately.
Clean the blade and blade flange washers
•
damage and tighten the arbor nut securely.
use only the blade flanges specified for this too
•
Keep your hands out of the path of the saw blade
•
your hands to be within 7-1/4" of the saw blade, the work piece should be clamped in place before making
the cut.
50 Feet
75 Feet
18
18
18
16
14
12
10
do not Let CoMFort or FAMiLiAritY witH produCt (gAined
until it is assembled and installed according to the instructions.
use only zero-degree or negative hook angles when using
iMportAnt
: Do not use thin kerf blades or blades with deep gullets. These can
that runs freely and is free of vibration.
100 Feet
18
18
18
16
16
14
14
12
12
10
10
10
8
8
. Check that the guards are correctly positioned, secured,
prior to operation. Replace a cracked or
prior to operation. Again, check for any
l.
. If the work piece being cut causes
.
Double insulated tools can use
150 Feet
200 Feet
16
16
14
14
12
12
12
10
8
8
8
6
6
6
, seek
.
5
Publicité
Table des Matières
