Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Settings
Setting up the receiver
Activating the network standby mode
You can keep the network function active even when the
receiver is in standby mode.
1
Select [Setup] - [System Settings] -
[Network/Bluetooth Standby] from the home
menu.
2
Select [On].
Note
• When the receiver is in standby mode, the (power) indicator on
the front panel lights up in amber if [Network/Bluetooth Standby]
is set to [On].
Turning on the control mode to make an
external controller connection
You can control the receiver from external devices.
1
Select [Setup] - [Install Settings] -
[External Control] from the home menu.
2
Select [On].
Note
• Set [External Control] to [On] to activate the network connection or
to activate control from an external controller connected to the
RS232C port.
Outputting a test tone from each speaker
(Test Tone)
You can output a test tone from each speaker in sequence.
1
Select [Setup] - [Speaker Settings] -
[Manual Speaker Settings] - [Test Tone] from the
home menu.
2
Select the setting you want.
Off
Auto: The test tone is output from each speaker in
sequence.
Front (L), Center, TV Center, Front (R), Surround (R),
Surround Back (R), Surround Back (L), Surround (L),
Height (L), Height (R), Subwoofer: You can select
which speakers will output the test tone.
3
Adjust the speaker level.
Tips
• You can set a test tone by pressing the TEST button on the remote
control. In this case, you can only use the display panel for the
operation.
• To adjust the level of all speakers at the same time, press +/–.
You can also use MASTER VOLUME on the receiver.
• The adjusted value is shown on the TV screen while adjusting.
12
EN
Displaying a test screen (Test Picture)
Display a test screen for HDMI OUT A (TV) and
HDMI OUT B/ZONE 2 jacks.
1
Press TEST on the remote control.
2
Select [Test Picture].
Tips
• A test picture is output in 480p from both the HDMI OUT A (TV)
and HDMI OUT B/ZONE 2 jack.
If you want to output a test picture in another resolution, select
[Setup] - [Install Settings] - [Test Picture for HDMI OUT A] or
[Test Picture for HDMI OUT B] from the home menu, and then
select the resolution setting you want.
• HDMI audio signals are not output while the test screen is
displayed.
Adjusting the sound balance automatically
(Auto Calibration)
This receiver is equipped with a D.C.A.C. IX (Digital Cinema
Auto Calibration) function, which allows you to perform
automatic calibration.
Auto Calibration allows you to perform automatic calibration
as follows.
– Check the connection between each speaker and the
receiver.
– Adjust the speaker level.
– Measure the distance of each speaker from your seating
position.
– Measure the speaker size.
– Measure the frequency characteristics (EQ).*
– Measure the frequency characteristics (Phase).*
* The measurement result is not utilized when [Direct] is selected.
Note
• The D.C.A.C. IX is designed to achieve proper sound balance for
your room. However, you can adjust the speaker levels manually
according to your preference using test tone.
1
Set up each speaker correctly, and then connect
the calibration microphone.
2
Select [Setup] - [Speaker Settings] -
[Auto Calibration Settings] - [Auto Calibration]
from the home menu.
3
Follow the instructions on the TV screen, then
press
to select [Start].
The measurement starts in 5 seconds.
The measurement process will take approximately one
minute with a test tone.
When the measurement ends, you will hear the
notification sound and the screen will switch.
4
Select the item you want.
Save: Saves the measurement results and exits the
setting process.
Retry: Performs the Auto Calibration again.
Discard: Exits the setting process without saving the
measurement results.
5
Save the measurement results.
Select [Save] in step 4.
Publicité
Table des Matières
