Publicité
Les langues disponibles
Les langues disponibles
•
Fit clamps to either side using M6 and M8 cap head bolts (NOTE THE CLAMPS BOTH HAVE
TAPERED BORES AND THIS MUST MATCH THE FRAME OR DAMAGE WILL OCCUR)
•
Ensure the no wires are trapped, tighten clamps and then the engine bar
•
Insert M12 bolt (used as a marking tool) into 12mm tapped hole as far as possible on outside of aluminium
block on one side
•
Paint middle of the bolt head
•
Refit fairing
•
Gently push fairing against the bolt head to leave a small paint mark on the inside of the fairing
•
Remove fairing
•
Centre drill on mark left by paint, working from inside of fairing outwards drill pilot hole in fairing and check
position by offering fairing back up and looking through hole (you may have to remove a small amount of
cladding)
•
Remove fairing and cut using 28mm hole saw (work from outside inwards)
•
Clean up the hole to leave it looking smooth. Trim the cladding on the inside of the fairing around the hole .
•
Repeat for other side, using the same bolt as marking tool as before
•
Replace fairings.
•
Place a washer behind the head of one of the M12 bolts followed by a shake proof washer and pass through
one of the protectors into counter bore.
•
Place one of the spacers provided over threaded end of the above bolt.
•
Pass assembly through the hole in the fairing and locate into tapped hole of aluminium block.
•
Tighten the assembly. PLEASE NOTE BOBBIN MUST BE POSITIONED AS PICTURED ABOVE
WITH BIGGER END TOWARD FRONT OF BIKE. Do not overtighten. Just tighten until you feel
some resistance from the compression sleeve inside the protector. Then 'nip' it up with a quarter turn on
your wrench. Do not overtighten as damage can occur to the bike. Do not exceed 40nm of torque.
•
Insert bobbin cap so logo is as shown above.
•
Repeat on other side.
Please note the OEM bolt maybe installed in the opposite direction in which case you may
have to reverse block installation order.
Due to the risk of cross-threading of bolts etc; we always recommend that our products be fitted by one of our official dealers or a
qualified mechanic.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The
Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those
in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for
its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify
any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the
motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a
replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise
than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises from accident or
neglect.
Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for
indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting
or service concerned. These terms do not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were
purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-
sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value
exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of
discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty
goods.
Unit 5K, Blacknest Industrial Park, Blacknest Road, Alton, Hampshire, GU34 4PX
Tel: +44 (0)870 220 6380 Fax: +44 (0)1420 521101
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
R&G Racing
www.rg-racing.com
Email:
info@rg-racing.com
Publicité
