R&G CP0148BL Instructions De Montage

FITTING INSTRUCTIONS FOR CP0148BL CRASH PROTECTORS
Please note that the way the kit is packed does not necessarily represent the way of mounting to the bike
Please note you will need 3 hands to do this job so please arrange some help before starting! Please also note that
in cases where kits are packed with rubber washers holding the components onto the bolt – the rubber washers
should be thrown away!
Nearside (left hand side as you sit on the bike)
•
Remove lower front engine bolt (you will have to use a 14mm spanner to hold nut on inside of engine)
•
Take one of the 110mm long cap head bolts and slide one of the 10mm washers up to the head of the bolt
•
Take left hand side block ( 6mm holes to bottom and spigot top right hand side facing bike) and slide the bolt
through 10mm hole in block before then sliding through the engine mount
•
Replace OEM nut onto bolt
•
Take two of the M6 cap head bolts and washers and fit through the block
•
Take one of the clamps and fit to inside of frame using 6mm bolts
•
Tighten all bolts firmly
•
Take the longest hex head bolt and slide one washer up to the head of the bolt
•
Slide bolt through one of the bobbins and the large black spacer
•
Fit to the block and tighten. Tighten bolt until you feel some compression from inside the protector. Turn a
little more so that you feel the compression increase slightly. Then apply a quarter turn. Do not overtighten
as damage can occur to the bike. Do not exceed 40nm of torque.
•
Be careful not to strip threads!
Offside
•
Repeat nearside process (note that no large black spacer is required on this side)
Due to the risk of cross-threading of bolts etc; we always recommend that our products be fitted by one of our official dealers or a
.
qualified mechanic
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not
diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or
warranty (other than as to title) has been given or will apply to the Products other than those in R&G's order or confirmation and the Buyer confirms it
has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other
services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is
responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall
at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained
otherwise than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises from accident or neglect.
Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or
consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These
terms do not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased direct
from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the opinion of R&G
Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value
purchase). The customer must pay any and all carriage charges. No returns of iscontinued products, unless within 14 days of purchase. This policy does
not affect your statutory rights and does not refer to faulty goods.
Unit 5K, Blacknest Industrial Park, Blacknest Road, Alton, Hampshire, GU34 4PX
Tel: +44 (0)870 220 6380 Fax: +44 (0)1420 521101
SUZUKI BANDIT 650 '05-'06 (AIR COOLED)
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
R&G Racing
www.rg-racing.com
exc. P&P – at the prevailing price at time of
Email: info@rg-racing.com